|
||
|
24th April 2024, 06:27 | #1 |
I really should get out more.......
Rover 75 1.8 Club Join Date: Dec 2013
Location: Tilburg (Netherland)
Posts: 2,615
Thanks: 572
Thanked 336 Times in 247 Posts
|
Replacing CV joint covers? What do I need?
Hello everybody,
During my last MOT the mechanic advised to replaced the CV joint covers. There was a tiny split in the rubber cover on 1 side, and the other one looked worn as well. I have done quite a bit of work on cars, but never done these items. Is there a How-to? Or can somebody explain it to me? From what I think: - Remove the wheel - Remove the brake disc - Remove wheel hub/bearing - Disconnecte the drive shaft from the hub - Slide the old cover from the drive shaft - Slide the new cover over the drive shaft - Reconnect everything back But I might be missing crucial steps? Anything else I should be doing while I'm tackling this job? Something servicable that I should do while I'm at it? Maybe something I should look out for? Also, would I need special tools? Or are basic household tools sufficient? Any pointers or advice is very welcome. I enjoy working on cars and learning and I want to do a good job ;-).
__________________
Proud owner of the Dutch "Golden 75". A much loved Gold White Metallic Rover 75 1.8 na from 2000. |
24th April 2024, 06:55 | #2 |
Loves to post
Rover 75 Tourer Join Date: Mar 2016
Location: Nantwich
Posts: 274
Thanks: 102
Thanked 31 Times in 23 Posts
|
|
24th April 2024, 07:10 | #3 | |
I really should get out more.......
Rover 75 1.8 Club Join Date: Dec 2013
Location: Tilburg (Netherland)
Posts: 2,615
Thanks: 572
Thanked 336 Times in 247 Posts
|
Quote:
A bit more like "replacing CV cover for dummies" ;-). Not that I am a dummy, but I like to make absolutely sure that I do everything by the book and that I won't get into trouble on the motorway haha. I did read a comment that said it is easier to take the driveshaft out, and I kinda wonder how easy this is. Sounds like it makes the whole job a lot easier.
__________________
Proud owner of the Dutch "Golden 75". A much loved Gold White Metallic Rover 75 1.8 na from 2000. |
|
24th April 2024, 07:26 | #4 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,573
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
I've done this job Vinnie. I'll consult my notes and get back to you shortly. You will need a special tool because the small diameter of the boot won't pass over the outer CV joint. You don't have to remove the driveshaft.
Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
24th April 2024, 08:34 | #5 | |
This is my second home
Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4. Join Date: Jul 2009
Location: Hampshire
Posts: 11,579
Thanks: 3,470
Thanked 3,119 Times in 2,247 Posts
|
Quote:
It's a bit easier than that - undo the driveshaft nut remove the hub lower clamp bolt and split the steering track rod end ball joint and you can withdraw the driveshaft from the hub. I prefer to do them on the bench and last time round I used a stretch rubber boot that you can fit without stripping the driveshaft down - it came with a cone and lub to guide it over. |
|
24th April 2024, 08:48 | #6 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,573
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Quote:
Simon Edit: I can provide that Vinnie if you confirm by P.M. that you still want it.
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. Last edited by SD1too; 25th April 2024 at 10:18.. Reason: Offer |
|
25th April 2024, 14:10 | #7 | |
I really should get out more.......
Rover 75 1.8 Club Join Date: Dec 2013
Location: Tilburg (Netherland)
Posts: 2,615
Thanks: 572
Thanked 336 Times in 247 Posts
|
Quote:
I'll sent you a PM Simon.
__________________
Proud owner of the Dutch "Golden 75". A much loved Gold White Metallic Rover 75 1.8 na from 2000. |
|
26th April 2024, 07:59 | #8 | |
This is my second home
Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4. Join Date: Jul 2009
Location: Hampshire
Posts: 11,579
Thanks: 3,470
Thanked 3,119 Times in 2,247 Posts
|
Quote:
Yes and no - the nearside pulls out but on the offside you have to unbolt the support bearing bracket. If you do one side at a time and jack the vehicle up from the side you shouldn't lose any gearbox oil. The driveshafts themselves clip into the gearbox so you you'll need a lever to spring them out - bit of flat bar, large screwdriver or similar. You can replace the driveshaft oil seals whilst you are there, but mine are 24 years old have covered 442k miles and still don't leak. |
|
|
|