|
||
|
12th November 2015, 19:26 | #1 |
Newbie
MG ZT Join Date: Nov 2015
Location: Leamington Spa
Posts: 9
Thanks: 0
Thanked 2 Times in 2 Posts
|
Valve Guide / HGF / Liner Diagnosis
Hi everyone,
It's my first post here, but I'm looking for help in the next steps I should take after I took my cylinder head off. Its a 1.8 K-series engine. Previously had the head gasket done about 1 1/2 years ago. The problems started again when I was getting intermittent rough idling when starting, either hot or cold. Sometimes it was light, sometimes severe, but always went away immediately with a few revs. It was also using a small amount of coolant and oil, maybe a few hundred ml every few months. Then one day sitting in traffic it overheated, completely to the red (I was looking for somewhere to pull over). But as soon as it hit the top I turned it off. Initially I replaced the inlet manifold gasket, replaced the thermostat, drained and bled the coolant. This didn't change anything though, still had the rough idling, and now every time I took the expansion cap off there was a lot of pressurised air coming out that smelt like exhaust gas. Also the exhaust seemed a little bit steamy, but could have been normal. Doing a (cold, dry) compression test I found lots of oil around the #1 spark plug thread. Can't remember the exact results but it was something like 100%, 105%, 50%, 60% relatively. So anyway off it came, interestingly I found that some of the cam cover bolts were not even finger tight, just completely loose. And here's what I found inside: The liners were not protruding from the block as far as I can tell. They are at least level, and in some places below. But there are no serious indentations in the head from the liners. #2 cylinder has a very sticky oil residue: With a sticky valve stem: The others more dry: There is a white crusty residue mostly one one side of the head: And less on the other side: The whole thing: So what do you think the next steps should be?
Or let me know if there are any other tests I can do to help diagnose. Your help is much appreciated. Thanks James Last edited by bitsofbeards; 12th November 2015 at 19:31.. Reason: Images didn't work |
12th November 2015, 20:05 | #2 |
Discount MG Rover Spares
Rover 75 CDTi, 2x MG ZS180 Join Date: Jun 2011
Location: Hythe, Southampton
Posts: 11,320
Thanks: 456
Thanked 3,377 Times in 2,027 Posts
|
I'm sure others will advise on the other issues, but from the point of view of liner heights - have a read of this:
Head Gasket Choice Guide It goes into depth about which gaskets you can use with which liner heights - should give you some pointers.
__________________
Your trusted MG Rover specialist! Tel: 02380 001133 / Email: [email protected] We now have a 'chat' function on our site for even quicker replies. Give it a try! Remember - discount code FORUM5 for 5% off |
13th November 2015, 07:26 | #3 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,338
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Quote:
I think that you've already carried out an excellent investigation. My initial thoughts are that checking the head height (there is a minimum dimension) and surface would be a good start, but I wouldn't reassemble the engine without looking more closely at that rough looking valve stem. If I were in your shoes, I would continue with your own engine and read the experiences of club member Beinet1 who has a lot to offer on the subject of 1.8 cylinder heads. When you say "get a new head" you don't mean "new" literally do you? I would not risk an unknown second hand part from e-bay. You could easily end up with more problems. Don't attempt to remove the liners, and don't turn the engine whilst the head is off. I don't see any evidence of a piston ring problem. So, in summary, I'd say keep going James! Remove the valve gear and carry out a cylinder head overhaul. Don't skim the head unless you have proof that it's necessary, and take care with gasket selection and all the other things applicable to a successful 1.8 engine repair. All the tips and tricks are here on the forum, together with continuing advice as you proceed. Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
|
13th November 2015, 17:20 | #4 |
Posted a thing or two
mg zt Join Date: Mar 2014
Location: cardigan
Posts: 1,087
Thanks: 28
Thanked 187 Times in 158 Posts
|
Hmmm, i agree you need to strip and overhaul the head, have a real good look at the surface, take it to an engineering shop to check. Personally i would skim it if there is the slightest hint of fire ring damage on the exhaust side. ( it looks like it hasnt been overly skimmed previously, going by the squish slots on its face). Dont be frightened by people telling you you cant skim these, ive taken 40 thou off them with no issues.
The more important thing you need to check is the liner heights, front and back. They need to be level in theblock, and all about the same height. If the liners have dropped due to overheating, the block is scrap, dont waste time on it. Rings on these engines rarely give trouble, covering 100+k easily, so id be suprised if this is your problem. |
13th November 2015, 18:42 | #5 |
I really should get out more.......
Rover 75 saloon Join Date: Feb 2014
Location: London
Posts: 2,952
Thanks: 263
Thanked 538 Times in 431 Posts
|
Have a look at this:
http://modusengineservices.co.uk/k-series/ Seems like it could be worth the money which sounds far from unreasonable.
__________________
Reducing the size of my Rover fleet by adding a 75 to it. |
13th November 2015, 19:52 | #6 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,338
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Quote:
Nice one Gary. Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
|
13th November 2015, 20:38 | #7 |
I really should get out more.......
Rover 75 saloon Join Date: Feb 2014
Location: London
Posts: 2,952
Thanks: 263
Thanked 538 Times in 431 Posts
|
Thanks, l posted about it a while back after spotting the link somewhere. If my headgasket goes at some point then l'll definitely be ordering one. At that money it seems a no-brainer to get the job done once & for all.
__________________
Reducing the size of my Rover fleet by adding a 75 to it. |
14th November 2015, 11:45 | #8 | |
Newbie
MG ZT Join Date: Nov 2015
Location: Leamington Spa
Posts: 9
Thanks: 0
Thanked 2 Times in 2 Posts
|
Quote:
I measured the liner heights more accurately with a feeler gauge and the flat side of a caliper. I got at least .05mm all around. So assuming I go with the MLS gasket how difficult is fitting the uprated oil rail? Is it worth it or just stick with the elastomer one? Hi Simon, Thanks so much for the encouragement! Getting a new head is more of a time saving thing really, rather than restoring the old one. When I say new I mean something like this. As mine has overheated at least twice now I'm not sure if it would be economical to not get a new one. Do you think I could just drop the old cams on that ebay one? Also I'm almost certain that the head isn't flat now, I can see that the gasket hasn't sealed properly around #2. The defined ring around the others fades at the rear of that cylinder. It looks like it was running a lot cooler than the others (less scorching and brown bits). And also the valves are stained purple, I'm assuming from coolant. I don't see how the cost of skimming an old head with dodgey valves is better than just getting brand new one. Assuming they come flat and everything? So I'm thinking, new head, gaskets etc, new water pump, and new coil packs just to be sure it wasn't an electrical problem causing the rough startup after all. Hopefully that will be enough to get a few more years out of it. What do you think? Oh, one further thing, one locating hole for the lug on one side of my head has a hole drilled about 3" deep that goes nowhere. The other side doesn't have this. It looks like someone has just stuck a drill down it at an odd angle. Anyone know what this is? Thanks James Last edited by bitsofbeards; 14th November 2015 at 11:54.. |
|
14th November 2015, 13:00 | #9 | ||
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,338
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Quote:
"Liners can be level with, or 0.075 mm above, the face of the block. If the liners have dropped below the block face the engine must be replaced. Check the cylinder liner by placing a straight edge across the liner and using a feeler gauge measure the distance between the cylinder block surface and the straight edge. This must be carried out in the inlet and exhaust manifold sides of the liner." The bulletin also says that the head face must be flat across the centre and from corner to corner, again using a straight edge and feeler gauge, to within 0.05 mm. It goes on: "Look for any sign of an indentation made by the bore eyelets of the head gasket. If there is an indentation ... the head has been overheated and the heat treatment properties ... lost. The cylinder head must be replaced." Quote:
Be sure that the Land Rover head you are considering buying is the same design as that used on the Rovers and MGs. There are differences between the vehicular applications sometimes. Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
||
14th November 2015, 14:59 | #10 |
Discount MG Rover Spares
Rover 75 CDTi, 2x MG ZS180 Join Date: Jun 2011
Location: Hythe, Southampton
Posts: 11,320
Thanks: 456
Thanked 3,377 Times in 2,027 Posts
|
0.05mm is 1.96 thousandths of an inch - if any are that low, you need to use the BW750 gasket.
We do a variety of BW750 kits - click here. MLS needs 3 thou or above all round, and perfectly even.
__________________
Your trusted MG Rover specialist! Tel: 02380 001133 / Email: [email protected] We now have a 'chat' function on our site for even quicker replies. Give it a try! Remember - discount code FORUM5 for 5% off |
Thread Tools | |
Display Modes | |
|
|