Ultrasonic Alarm Module & Fitting Equip

Nomisf · 27th November 2010, 12:20

Item is now sold, thanks.

Hi,

I have the volumetric sensor assembly from the upgraded alarm system, complete with back plate, sensor module, and cover plate. The cover plate is a little grubby but should clean up nicely. Part is YWC 112250 : http://www.rimmerbros.co.uk/Item--i-YWC112250

£20 + £5 p+p

phenonix · 28th November 2010, 01:01

PM sent for this

Kearton · 30th November 2010, 21:12

Quote:

Originally Posted by Nomisf

Hi,

I have the volumetric sensor assembly from the upgraded alarm system, complete with back plate, sensor module, and cover plate. The cover plate is a little grubby but should clean up nicely. Part is YWC 112250.

Hi,
did you remove this yourself? If so, please can you post details of how to do it safely? I had a go a while back but gave up when it seemed that I would pull the lining off too.

Regards,
Kearton

VVC-Geeza · 30th November 2010, 21:50

Can this be added to any of the alarm systems?

Nomisf · 1st December 2010, 08:07

Hi All,

I am not sure on the fitting requirements, will need a t4 guru to pop in really.

To remove it, there is a ring above the headlining which clips to the unit below the headlining. The two come apart with clips- I simply prised it out with my fingers, just going slowly and gently around the edge, applying even pressure. Once this main part is off, the rest is fairly obvious as all the fixings can be seen.

Regards,
Simon

Kearton · 1st December 2010, 21:24

Quote:

Originally Posted by Nomisf

Hi All,

To remove it, there is a ring above the headlining which clips to the unit below the headlining. The two come apart with clips- I simply prised it out with my fingers, just going slowly and gently around the edge, applying even pressure. Once this main part is off, the rest is fairly obvious as all the fixings can be seen.

Regards,
Simon

Thanks Simon

27th November 2010, 12:20	#1
Nomisf Regular poster 53' MG ZT-T CDTi+ Join Date: Jul 2010 Location: Reading Posts: 52 Thanks: 0 Thanked 0 Times in 0 Posts	[Sold] Ultrasonic Alarm Module & Fitting Equip Item is now sold, thanks. Hi, I have the volumetric sensor assembly from the upgraded alarm system, complete with back plate, sensor module, and cover plate. The cover plate is a little grubby but should clean up nicely. Part is YWC 112250 : http://www.rimmerbros.co.uk/Item--i-YWC112250 £20 + £5 p+p __________________ 53' MG ZT-T CDTi+ Last edited by Nomisf; 3rd December 2010 at 07:20..

28th November 2010, 01:01	#2
phenonix Posted a thing or two Rover 75 2001 Club Sedan V6 2.5 Join Date: Mar 2007 Location: Sydney Posts: 1,458 Thanks: 18 Thanked 9 Times in 6 Posts	Sensor PM sent for this

30th November 2010, 21:50	#4
VVC-Geeza This is my second home 2005 Connoisseur SE 1.8 Turbo,2004 45 1.8 Connoisseur and my beloved 1998 VVC Coupe. Join Date: Nov 2009 Location: Derby. Posts: 8,757 Thanks: 2,022 Thanked 1,016 Times in 739 Posts	Can this be added to any of the alarm systems? __________________

1st December 2010, 08:07	#5
Nomisf Regular poster 53' MG ZT-T CDTi+ Join Date: Jul 2010 Location: Reading Posts: 52 Thanks: 0 Thanked 0 Times in 0 Posts	Hi All, I am not sure on the fitting requirements, will need a t4 guru to pop in really. To remove it, there is a ring above the headlining which clips to the unit below the headlining. The two come apart with clips- I simply prised it out with my fingers, just going slowly and gently around the edge, applying even pressure. Once this main part is off, the rest is fairly obvious as all the fixings can be seen. Regards, Simon __________________ 53' MG ZT-T CDTi+