|
||
|
|
12th November 2006, 16:26 | #1 |
This is my second home
Waiter, Waiter! I seem to have a Roomster in my drive... Join Date: Nov 2006
Location: Sussex
Posts: 3,268
Thanks: 0
Thanked 1 Time in 1 Post
|
bonnet/bumper shutline adjustment
has anyone got any actual measurements for what is desirable/achieveable? I have only started looking at the shutline now I've put the bumper back on, and it now looks too large although I read the How to - very good - and adjusted according to the notes there.
I did wonder how one is able to move the bumper UP... the bolts along the top edge dont seem to account for this. Are some people using spacers underneath the plastic panel and if so, what spec? |
12th November 2006, 16:39 | #2 | |
Banned
180+ Sport Auto Join Date: Oct 2006
Location: Bedford Middle Level
Posts: 17,787
Thanks: 0
Thanked 18 Times in 5 Posts
|
Quote:
There aren't any measurments as such, I think as much as you can get out of it is the best you can hope for. I had someone insert washers while I lifted the bumper, took a few goes before I was satisfied. |
|
12th November 2006, 16:45 | #3 |
Owners Club Director
Rover 75 V6 Copperleaf Red, MG ZTT 190+ Lagoon & Early MGF Join Date: Oct 2006
Location: Rugby
Posts: 9,287
Thanks: 105
Thanked 343 Times in 81 Posts
|
Silly point Grey Ghost, but is there any benefit to using non-metal washers to try and stave of local rusting at these point?? I need to adjust teh shutline on mine and am thinking that what you describe above is the only way for me as I have no more play using the existing "settings".
Cheers
__________________
Christopher in banana veritas |
12th November 2006, 16:51 | #4 | |
Banned
180+ Sport Auto Join Date: Oct 2006
Location: Bedford Middle Level
Posts: 17,787
Thanks: 0
Thanked 18 Times in 5 Posts
|
Quote:
|
|
12th November 2006, 20:39 | #5 |
This is my second home
ZT400 Join Date: Oct 2006
Location: Ellesmere
Posts: 5,948
Thanks: 0
Thanked 43 Times in 29 Posts
|
Jon most of the adjustment should be done by the bolts holding the alloy cross member that the slam panel bolts on to if fitted correctly washers should not be necessary imho
|
13th November 2006, 13:45 | #6 |
This is my second home
Waiter, Waiter! I seem to have a Roomster in my drive... Join Date: Nov 2006
Location: Sussex
Posts: 3,268
Thanks: 0
Thanked 1 Time in 1 Post
|
ahhh... very interesting. An alternative school!
So, do I surmise from this that, iyho, the alloy cross member should just be pulled as high as it can go before being tightened... and that it, with gravity, can slip a bit over time causing people to find other avenues to solve this problem? Surely the cross member couldnt be, by default, suggested as a trimming device as it is a stage further back in the process! If so it would seem frightfully inefficient...taking bumper on and off and resetting the member? |
13th November 2006, 13:58 | #7 | |
Owners Club Director
Rover 75 V6 Copperleaf Red, MG ZTT 190+ Lagoon & Early MGF Join Date: Oct 2006
Location: Rugby
Posts: 9,287
Thanks: 105
Thanked 343 Times in 81 Posts
|
Quote:
Cheers
__________________
Christopher in banana veritas |
|
|
|