|
||
|
17th January 2023, 07:42 | #331 | |
Newbie
None at the moment Join Date: Nov 2022
Location: Viljandi
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
Thank you guys, will ask them.
Quote:
That's why I hope to get some diagram for it, a user in here got one, so hoping someone in here knows where to get it. I tried to search Hella diagrams every way I could, but no luck. Regards Keijo |
|
17th January 2023, 08:54 | #332 | |
This is my second home
Rover 75 Saloon & Tourer Join Date: Sep 2012
Location: Lincoln
Posts: 15,005
Thanks: 1,630
Thanked 3,032 Times in 2,181 Posts
|
Quote:
Have you contacted Trebor or Devilish as previously suggested? macafee2 |
|
17th January 2023, 12:05 | #333 |
Newbie
None at the moment Join Date: Nov 2022
Location: Viljandi
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
yes I have. thanks
Keijo |
17th January 2023, 13:06 | #334 |
This is my second home
75 Tourer Join Date: Apr 2009
Location: Cannock
Posts: 4,133
Thanks: 3
Thanked 189 Times in 121 Posts
|
you have a PM Keijo
__________________
If at first you don't succeed, hide the evidence |
10th February 2023, 09:33 | #335 |
Newbie
None at the moment Join Date: Nov 2022
Location: Viljandi
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
Meanwhile I have taken out FBH and did some testing.
The common suspicious resistors were ok, but I had several resistors out of range (13 resistors in total), but not totally shorted or open. See attached pictures. No bad solder joints found. I don't know if these values are enough to create problems. I also did the component tests with WTT on the table (21W bulb in place of the fuel pump) and measured voltages on driver FETs legs. Pictures of scope patterns also attached. Drain of all the FETs showed battery voltage at all times. Source voltages were all 0 while components switched off (except circulation pump, which showed 2V, strange). Gate voltages were all close to 0 (20...50mV) while components switched off (except circulation pump, which showed around 1.45V, again strange). When components were turned on, the source voltages were as expected, only circulation pump did nothing. See pictures. Gate Voltages had very high peaks, I don't know if it is normal or not. Gate voltages on Fan and Circ. pump FETs were around 200V and very noisy, big ripples. Again, don't know if it's normal or might be caused by some bad capacitors. It can be only seen with scope, the multimeter shows 16,5V at Fan FET's gate, 4,3V at FP FET's gate, and 14.5V at GP FET's gate while running. I wanted to try the 21W bulb in place of circ. pump, but decided to try the old pump first. And it seemed to work perfectly, turned on and ran every time commanded. With the working pump connected, but not running, The voltages were 0.94V on the source pin and 0.41V on the gate pin. Another thing I noticed, is that there is no voltage drop on Circulation Pump's FET (between source and drain) while running, but for example on Fan's FET there is a drop of about 1.2V. From this information is it possible that the CP FET itself is faulty? PS. Does anyone know how can I start FBH with WTT software from the "control" tab? It is greyed out for some reason. Any thoughts? Keijo Pictures: https://www.dropbox.com/s/j0uuj7vpmc...8__01.jpg?dl=0 https://www.dropbox.com/s/j0uuj7vpmc...8__01.jpg?dl=0 https://www.dropbox.com/s/3ax5bmn548...20Off.JPG?dl=0 https://www.dropbox.com/s/p8hsm08sgj...tered.JPG?dl=0 https://www.dropbox.com/s/2aq877k9to...20Fan.JPG?dl=0 https://www.dropbox.com/s/mqnu9cz1bj...0Pump.JPG?dl=0 https://www.dropbox.com/s/8ifdmg96yv...0Plug.JPG?dl=0 |
Thread Tools | |
Display Modes | |
|
|