|
||
|
18th April 2022, 07:38 | #81 |
Guest
Posts: n/a
|
|
18th April 2022, 07:45 | #82 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,386
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
A question
Quote:
Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
|
18th April 2022, 08:57 | #83 | |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Quote:
|
|
18th April 2022, 09:04 | #84 |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
|
18th April 2022, 12:27 | #85 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,386
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
OK Jon thanks. What about if the suspension arm is to be refitted?
Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
18th April 2022, 12:45 | #86 |
Loves to post
55 cdti tourer slush box executive grill Join Date: Feb 2022
Location: Sheffield
Posts: 380
Thanks: 40
Thanked 85 Times in 72 Posts
|
You don't hit the threaded part of the taper you hit the subframe adjacent to the taper the resulting shock releases it ,if you run the nut so it is flush with the end of the thread and jack the car up so the weight of the car is on it (the nut giving a bigger footprint for the Jack)the upward force helps with the release, then if the nut spins after release just force the taper back in with a bar undo the nut and prise back out with the bar or prise and tap the subframe again and it will pop right out
|
18th April 2022, 12:52 | #87 | |
Loves to post
MG ZT-T CDTi Join Date: Sep 2020
Location: Lincs
Posts: 288
Thanks: 73
Thanked 51 Times in 44 Posts
|
Quote:
In short leave the nut on the end then once wacked loose cut the nut off remove and clean the end up as pin thread should be long enough to refit if arm still in serviceable condition. I tried to put a nut on it but didnt have the right thread pitch to hand nor a m14 die to retap so did it without and was careful not to mash it up. did have to dress the end of the pin a couple of times when it became damaged and even split due to unsuccessful separator attempts on it ripped it to pieces. In the past i have had that trouble and then just loosened the nut off enough to get a hacksaw blade in to cut pin off as need be as nnot posh enough to own a disc cutter. The nut that came off was totally threaded and it destroyed the thread coming off, once the nut was off I had to cut a half inch off the thread for the separators to fit so leaving about the same again exposed. The pullers managed to split the end of the threaded pin further but once cleaned up with a file and chisel i made sure to round the edges with the file and flatten the end. I did not want to keep wacking it to form a rivet so eventually found the right tool (a 7lb sledge hammer lol) lined it up and three good laser guided wacks i spent more time setting it up, getting the car high etc than hitting it. The end of the pin was slightly bulged but it slipt through the hole in the sub frame without drama, they would have heard my words on Mars otherwise lol. I also seem to have troubles with the outer tie rod (prefer to move it up out the way to get to the bush bolts), these always seem to get a mashed up top nut and the Alan key middle always mashes up to leaving them stuck on ironically i never once took a splitter to it. Have found using a jack on the bottom of the tie rod to apply pressure up so the taper is firmly gripped by the hub then a mashed up nut will come off saving the tie rod and just put a new nut on which again is not the standard thread i think its one more size up.
__________________
ZT-T Mk2 Jobs to do: Renew auxiliary drive belt # Replace driver door lock actuator # Refurbish wheels Last edited by Retap; 18th April 2022 at 13:11.. Reason: If you want it then hya betta put a nut on it. |
|
18th April 2022, 12:53 | #88 | |
Loves to post
MG ZT-T CDTi Join Date: Sep 2020
Location: Lincs
Posts: 288
Thanks: 73
Thanked 51 Times in 44 Posts
|
Quote:
Defo if your posh.
__________________
ZT-T Mk2 Jobs to do: Renew auxiliary drive belt # Replace driver door lock actuator # Refurbish wheels |
|
18th April 2022, 12:54 | #89 | |
Loves to post
MG ZT-T CDTi Join Date: Sep 2020
Location: Lincs
Posts: 288
Thanks: 73
Thanked 51 Times in 44 Posts
|
Quote:
I am converted brother Colvert. You just canne beat a good wack with a lump of iron.
__________________
ZT-T Mk2 Jobs to do: Renew auxiliary drive belt # Replace driver door lock actuator # Refurbish wheels |
|
18th April 2022, 12:59 | #90 | |
Loves to post
MG ZT-T CDTi Join Date: Sep 2020
Location: Lincs
Posts: 288
Thanks: 73
Thanked 51 Times in 44 Posts
|
Quote:
I can imagine this scenario applies if a garage cuts the subframe to remove an old arm and you want to save the new arm they put on for the new subframe you made the garage pay for or perhaps if breaking a car? Otherwise these arms are disposable really as removal can be destructive which is a shame as if it was possible to change the hub ball joint end it would save so much pain though i have found the inner balljoint usually starts getting loose not long after the outer goes wonky.
__________________
ZT-T Mk2 Jobs to do: Renew auxiliary drive belt # Replace driver door lock actuator # Refurbish wheels |
|
|
|