Go Back   The 75 and ZT Owners Club Forums > The 75 and ZT Owners Club Forums > The 75 and ZT Owners Club General Forum
Register FAQ Image Gallery Members List Calendar Mark Forums Read
Notices

Reply
 
Thread Tools Display Modes
Old 20th September 2016, 16:18   #21
Trisman
Avid contributor
 
Rover 75 saloon.

Join Date: Feb 2016
Location: S.E. London
Posts: 116
Thanks: 67
Thanked 31 Times in 22 Posts
Default

That's a fantastic write-up!

I wish it had existed when I fitted heated/electric seats to my car, as I went down the 'take a damn loom out of a donor car' route...

I can confirm that it's a complete pain & seemed to need most of the interior & dash removing... I ended up modifying my colossal loom anyway, to make re-installation easier.

Also, I didn't fancy a stuck seat-switch flattening the battery or starting a fire...
So I ran the live feed from a 12v supply that comes on with the ignition.

Questions:

Anyway, my seats are the non-memory type.

If I wanted to fit a memory driver's seat, would I need to convert the system so that it's always on, with a permeant live supply?

I would assume that the memory bit needs a permanent live, or is that taken care of by the K Bus link? (I'd guess not, as it seem the K Bus link wire is optional).

Would the memory be retained if just the memory part had a permanent live?
__________________
[SIGPIC][/SIGPIC]
Now gone: 2000 Rover 75 CDT. Manual. Tahiti blue (JRJ).

Mods: EGR delete. Synergy 2E. In-line Thermostat. Electric, heated black leather seats. Chrome Skullcaps. Black steering wheel. 18" MG ZT 11 spoke wheels. Plenum spy-hole. In-dash Sat-Nav. Mesh grill.
Repairs: Rad fan. Clutch/flywheel. Exhaust. Rear light seals. Front bushes & ARB links. Springs. A/C regas. Alternator regulator. Window 'B' post trim.
Future: Remote boot release.
Front end drop, 160 remap..!?

Last edited by Trisman; 20th September 2016 at 17:34.. Reason: Typo.
Trisman is offline   Reply With Quote
Old 20th September 2016, 19:14   #22
Rick-sta
This is my second home
 
Rick-sta's Avatar
 
MG ZT 2.0 CDTI+ in Typhoon, MG TF 135 in Typhoon & Rover 75 Connoisseur CDTI SE in Pearl Black

Join Date: Oct 2012
Location: Norfolk
Posts: 7,523
Thanks: 2,718
Thanked 2,827 Times in 1,462 Posts
Default

Quote:
Originally Posted by Trisman View Post
That's a fantastic write-up!

I wish it had existed when I fitted heated/electric seats to my car, as I went down the 'take a damn loom out of a donor car' route...

I can confirm that it's a complete pain & seemed to need most of the interior & dash removing... I ended up modifying my colossal loom anyway, to make re-installation easier.

Also, I didn't fancy a stuck seat-switch flattening the battery or starting a fire...
So I ran the live feed from a 12v supply that comes on with the ignition.

Questions:

Anyway, my seats are the non-memory type.

If I wanted to fit a memory driver's seat, would I need to convert the system so that it's always on, with a permeant live supply?

I would assume that the memory bit needs a permanent live, or is that taken care of by the K Bus link? (I'd guess not, as it seem the K Bus link wire is optional).

Would the memory be retained if just the memory part had a permanent live?
Thanks James

It is a bit of a mission to remove the original loom isn't it? I couldn't believe how far back I had to remove the dash in order to get to the loom and still I had to cut it from one end and pull it through on the other as it was just impossible to get to.

I'm not too sure what the answer is to your question unfortunately. I believe the OEM set up had a permanent live powering the memory function on the drivers seat.

Do you know if the loom you fitted included the wiring for the memory function on the seats? If so it may be worth trying out a memory seat and see if it works.
__________________
How to retrofit Cruise Control on a diesel with no OEM wiring in place: Link
How to retrofit heated electric memory seats with no OEM wiring in place: Link
How to operate FBH and ATC via text Link
How to restore cloudy projector headlights Link
Rick-sta is offline   Reply With Quote
Old 20th September 2016, 19:41   #23
Trisman
Avid contributor
 
Rover 75 saloon.

Join Date: Feb 2016
Location: S.E. London
Posts: 116
Thanks: 67
Thanked 31 Times in 22 Posts
Default

Quote:
It is a bit of a mission to remove the original loom isn't it? I couldn't believe how far back I had to remove the dash in order to get to the loom and still I had to cut it from one end and pull it through on the other as it was just impossible to get to.
:lol: yes... I managed to get quite close to the fusebox, but by that point it was like unknotting cruise-liner mooring rope so, as I had something that included all the connections (both sides) plus all the heated seat switch connections, I gave up & cut the rest!

As it was a scrap donor car, (MY scrap donor car! ) cutting carpet & removing dash, centre console & a whole heap more was hardly an issue.
The seats were out anyway as they were going into my car. (I also learned the hard way that you need to keep them powered to unbolt them from the floor!).

Quote:
Do you know if the loom you fitted included the wiring for the memory function on the seats? If so it may be worth trying out a memory seat and see if it works.
No, it didn't. The seat connector had the holes for additional wires, but they weren't populated.

It wouldn't be the end of the world to run a couple of extra wires to power-up the memory, (I'd need the additional connector anyway) & if the cars came from the factory with the seats wired to a permanent live, they must've been fairly sure that my concerns about fire & flat batteries aren't really an issue!
__________________
[SIGPIC][/SIGPIC]
Now gone: 2000 Rover 75 CDT. Manual. Tahiti blue (JRJ).

Mods: EGR delete. Synergy 2E. In-line Thermostat. Electric, heated black leather seats. Chrome Skullcaps. Black steering wheel. 18" MG ZT 11 spoke wheels. Plenum spy-hole. In-dash Sat-Nav. Mesh grill.
Repairs: Rad fan. Clutch/flywheel. Exhaust. Rear light seals. Front bushes & ARB links. Springs. A/C regas. Alternator regulator. Window 'B' post trim.
Future: Remote boot release.
Front end drop, 160 remap..!?
Trisman is offline   Reply With Quote
Old 20th September 2016, 21:23   #24
Rick-sta
This is my second home
 
Rick-sta's Avatar
 
MG ZT 2.0 CDTI+ in Typhoon, MG TF 135 in Typhoon & Rover 75 Connoisseur CDTI SE in Pearl Black

Join Date: Oct 2012
Location: Norfolk
Posts: 7,523
Thanks: 2,718
Thanked 2,827 Times in 1,462 Posts
Default

Quote:
Originally Posted by Trisman View Post
:lol: yes... I managed to get quite close to the fusebox, but by that point it was like unknotting cruise-liner mooring rope so, as I had something that included all the connections (both sides) plus all the heated seat switch connections, I gave up & cut the rest!

As it was a scrap donor car, (MY scrap donor car! ) cutting carpet & removing dash, centre console & a whole heap more was hardly an issue.
The seats were out anyway as they were going into my car. (I also learned the hard way that you need to keep them powered to unbolt them from the floor!).



No, it didn't. The seat connector had the holes for additional wires, but they weren't populated.

It wouldn't be the end of the world to run a couple of extra wires to power-up the memory, (I'd need the additional connector anyway) & if the cars came from the factory with the seats wired to a permanent live, they must've been fairly sure that my concerns about fire & flat batteries aren't really an issue!
Mine was my own scrap donor car too, took me about 4 days spending a couple hours at time removing it.

Not sure which pins in the main black 8 pin plug are for the memory function apart from pin 6 which is the K-bus. I guess you could use my wiring diagram to work out which wires you require that are missing .

The later cars were wired to permanent live, as my dad's 04 plate 75 has factory fitted electric memory seats which can be operated without the key in the ignition
__________________
How to retrofit Cruise Control on a diesel with no OEM wiring in place: Link
How to retrofit heated electric memory seats with no OEM wiring in place: Link
How to operate FBH and ATC via text Link
How to restore cloudy projector headlights Link
Rick-sta is offline   Reply With Quote
Old 22nd September 2016, 21:39   #25
Rick-sta
This is my second home
 
Rick-sta's Avatar
 
MG ZT 2.0 CDTI+ in Typhoon, MG TF 135 in Typhoon & Rover 75 Connoisseur CDTI SE in Pearl Black

Join Date: Oct 2012
Location: Norfolk
Posts: 7,523
Thanks: 2,718
Thanked 2,827 Times in 1,462 Posts
Default

Quote:
Originally Posted by KRISTLEE View Post
I thought the wire had to come from the drivers seat? Isn't there a closer K-Bus to tap into? I have the wire as part of my loom I just decided not to use it as it wasn't necessary lol
Hi mate, I found a K-Bus wire you can tap into much closer to the Driver's seat I hadn't actually every connected my pin 6 to K-Bus to activate the memory function, so whilst sorting out my dodgy airbag connector under the driver's seat, thought I'd check the LSM wiring loom for a K-Bus wire.... and here you go, found one:





Apologies for the blurry first pic, didn't realise it took it blurry. There is a K-Bus wire within the wires going into the back of the LSM.

I tapped into this and wired it up to pin 6, and it works perfectly. I can now set programmed seat settings and it works just like the OEM set up with the chime noises
__________________
How to retrofit Cruise Control on a diesel with no OEM wiring in place: Link
How to retrofit heated electric memory seats with no OEM wiring in place: Link
How to operate FBH and ATC via text Link
How to restore cloudy projector headlights Link
Rick-sta is offline   Reply With Quote
Old 9th February 2017, 12:10   #26
ALBLOHE
Newbie
 
Rover 75 saloon

Join Date: Feb 2017
Location: Madrid
Posts: 25
Thanks: 25
Thanked 2 Times in 2 Posts
Default

Quote:
Originally Posted by Rick-sta View Post
Hi all,

Had been asked quite a few times for a how to on retrofitting electric heated memory seats to a 75 or ZT which doesn't have the original loom in place already. I performed this retrofit on my ZT back in 2014 and has worked perfectly fine ever since.

The guide below requires you to make your own loom, which is pretty easy and simple to do, and much much easier and quicker than trying to remove the original OEM loom from a donor car and trying to fit it to your own. I've removed an original loom from my old doner car last year and it required the whole dash to be removed, a lot of tape and cable ties to be cut before the wiring could be removed, and it look a long time to pick out the wires I needed.

The guide below is just the way I did it and it worked for me, it may not be the best way to do it or the way you would do it, but for those that don't know where to start, this will be be a good starting point and you can feel free to do parts differently as you wish . By wiring up the seats this way, the power to the seats is permanent live, meaning you can move the seats without having the key turned in the ignition. The heated seat function only works with the key turned in the ignition.

At the time I used electrical connector blocks to wire up the seats, however if you can, I would recommend soldering the wires and using heat shrink sleeves over the joints. If you choose to use electrical connectors like myself, then ensure you use the correct rated blocks and properly insulate the joints using electrical tape.

What you'll need:
Driver and Passenger seat large black 8 pin plugs (car side) with about 6 inches of wiring on each.
Heated seat plugs with about 6 inches of wiring (car side)
30amp rated wiring http://www.ebay.co.uk/itm/1mm-1-5mm-...gBtK2D7Gerf5xg
5amp rated wiring http://www.ebay.co.uk/itm/AUTOMOTIVE...29Dx4YNkFV4qcQ
Female Spade Crimp Connectors x2 http://www.ebay.co.uk/itm/Insulated-...z0wGxMA4V4CMWw
Crimp Ring Connectors x2 http://www.ebay.co.uk/itm/Red-Blue-Y...hbeNJ3V413nt5w
Inline fuse holders x 5 http://www.ebay.co.uk/itm/5-x-Standa...UAAOSw0QFXC10X
Electrical connector Blocks/ or soldering iron if soldering http://www.ebay.co.uk/itm/3-6-15-30-...XI_Ohqnic6ygYQ
Wire Strippers
Screw Drivers
Socket Set + Extension Bar
T50 Torx bit
Electrical tape
Cable ties
Time: this took me 1 day to retrofit from start to finish.

Driver's seat plug:


Passenger Seat Plug:


Heated Seat Switch Plugs:



My Wiring Diagram:
This is a wiring diagram I made for myself a couple years back to help me with my retrofit. I'll explain all the parts of the diagram below, personally found it much easier to understand and follow the wiring using this:


Note: I made the wiring diagram above based on another how to I'd used, however when it came to wiring up my seats, I noticed that Pin 8 on both the driver's side and passenger side plugs were actually empty, therefore I'd advise checking if your 8 pin seat plugs have a wire in pin 8 or not. If you don't have a wire in pin 8, then ignore pin 8 on the wiring diagram above. If you do have a wire in Pin 8, I believe this is will need to be connected to a 30amp live.

What the wires on each plug are for:

Drivers Seat:
The Driver's side plug has the following pins:

Pin 1 - (thin Yellow Wire): Wire for heated seat switch (goes to pin 2 of the heated seat switch)
Pin 2 - (thin Orange/White): Power wire for Heated Seat (Ignition Live)
Pin 3 - (Black): Earth
Pin 4 - (Orange/White) : Live 30 amp
Pin 5 - (Brown/Pink wire): Live 5 amp
Pin 6 - K-Bus wire for memory function, simply wire to a K-Bus wire behind the dash. (can ignore if you wish)
Pin 7 - (Black/Slate): Earth
Pin 8 - Empty

Passenger Seat:
The passenger side plug has the following pins:

Pin 1 - (thin Yellow Wire): Wire for heated seat switch (goes to pin 2 of the heated seat switch)
Pin 2 - (thin Orange/White): Power wire for Heated Seat (Ignition Live)
Pin 3 - (Black): Earth
Pin 4 - Empty
Pin 5 - (Brown/Pink wire): 5 amp Live Power
Pin 6 - Empty
Pin 7 - Empty
Pin 8 - Empty


Heated Seats:
The heated seats switches for the dash have the following wires:

Pin 1: Thick (1.5mm) Black = Earth
Pin 2: Thick (0.75mm) Yellow = Connect to yellow from the seat plugs (Pin 1 on seat plugs)
Pin 3: Thin (0.5mm) red/white = this is for the illumination of the switch when the lights are switched on, simply wire to another red/white sidelight circuit wire behind the centre consol.
Pin 4: Thin (0.5mm) orange/white = ignition live feed, this is simply for the green light which illumates when the heated seat switch is turned on, simply wire this to a ignition live cable behind the centre consol.

Remember to Disconnect the battery before starting.

Removing Front Seats:
First step would be to remove your current front seats, both seats are held in place with 4 bolts on the runners. This is pretty straight forward to do:

1. move seat as far back as possible.
2. Remove torx bolt at front of each runner
3. move seat as far forward as possible
4. Remove torx bolt at rear of each runner
5. Tilt seat forward or back and unclip electrical connectors under seat ( good practice to disconnect battery before disconnecting connectors as one is the airbag for each seat)
6. remove headrest
7. carefully remove from car

Power for seats:

Before starting, ensure you have disconnected the car battery.

I started off my wiring by getting the power sorted to the seats. The power is taken from fuse slots 19 and 21 from the fusebox behind the glove box , which based on my owners manual is where the fuses for the OEM electric seats are. This is based on the later fuse box which takes the smaller mini fuses. If you have an earlier model with the older fuse box which takes the larger fuses, I believe the electric seats fuse slots are still slots 19 and 21 according to the older owners manual. You will require 2 30 amp fuses for the fuse box.

Now there are three ways you can wire your power wires to the fuse box:
1. Unbolt the fuse box and use female spade connectors to slot into the two blank slots (19 and 21) from behind the fuse box.
2. use piggy back fuse holders to take the power from the front of the fuse box (30 amp rated piggy back fuse holders will be required).
3. Take a power from the tow bar electrics plug.

Option 1:
I personally used option 1, and unbolted the fuse box and wired to the fuse box from behind using two female spade connectors. This is quite fiddly, but looks a bit neater when done. If you choose to do it this way, ensure the femal spade connectors you use are the correct size to hold the pin on your fuses. I have explained how to wire to the fuse box using option 1 below.

Option 2:
Option 2 is a lot easier, however I am not sure if you can purchase 30amp rated piggy back fuse holders, the highest rated ones I've been able to find are 20amp. Maybe someone would be able to confirm if it is possible to obtain 30amp rated ones, which is what will be needed. I would suggest using two seperate piggy back fuse holders, one for the drivers seat and one for the passenger seat.

Option 3:
I haven't used this option myself, but another option is to use the tow socket wiring which I believe is found to the left of the fuse box within the large bunch of wires. There is an orange and grey thick wire going into a black plug as shown in the pic below. This is the 50amp live for the towing socket. If you never intend on fitting a tow bar in the future, you could cut off the black plug and wire directly to the orange and grey wire (use a inline fuse holder here with a 30amp fuse), however if you have a tow bar or you think you may fit one in the future, you could piggyback off this wire using a scotch lock or a connector block, but I would advise to use options 1 or 2 incase you put too much load onto the orange and grey wire if using it for electric seats and your tow bar.



If you choose to use this option you will need to split your power cable into two cables, one for the passenger seat and one for the drivers seat.


Using Option 1:
The rest of this how to will be based on using option 1. Begin by unbolting and removing the glove box (how to remove glove box: http://www.the75andztclub.co.uk/foru...t=sunroof+leak) and then unbolt the fuse box which is held in place with two 8mm bolts on opposite corners (socket set and an extension bar came in handy here). Once removed, carefully turn the fuse box around, and you should be able to see that no wires go into fuse slots 19 and 21. Now you will need two lenths of your 30amp rated power cable, one will need to be long enough to reach from the fuse box to the passenger seat and the other needs to be long enough to reach the drivers seats. Once you have your two lenths, crimp a female spade connector to your power cables (on the end which will be connected to the fuse box) and insulate with electrical tape (or solder if you wish to and then insulate).

Now you will need to slot the two spade connectors into slots 19 and 21 of the fuse box from behind, and then plug in a 30amp fuse into slots 19 and 21 from the front. Below is a photo of this done on mine, the two thick red wires are the ones I slotted into the back of the fuse box. Once done, you now have your power feeds for the driver and passenger seats.



In order to run the power wires from the fuse box to under the driver and passenger seats, you will need to remove the plastic floor trims along the front driver's and passenger's doors, remove the plastic side trims in the foot wells on the outer sides (i.e. left side in the passenger foot well and right side on the drivers footwell where the boot and bonnet releases are), and lift up some of the carpet along the edges. You'll also need to remove the stereo and heater control panel in the centre consol at this point in order to pass the driver's seats power wire from the passenger side of the car to the drivers side.

I'd suggest ordering new plastic trim fastners prior to doing this as it's common for the trim fastners to snap when removing the plastic floor trims, replacement ones are available on ebay: http://www.ebay.co.uk/itm/ROVER-SILL...-/190864489736

One you've removed the necessary trims, you'll need to run your passenger power cable down the left side of the passenger footwell and under the carpet to under the passenger seat, and run the driver's side power cable across behind the dash past the centre consol, down the far right of the driver's footwell, down behind the boot and bonnet release and then under the carpet to under the driver's seat.






Now you have power to the driver and passenger seats.

Wiring up the Driver's Seat:
Power:
Starting with the power cable you will need to split this into 3 live feeds for pins 2, 4 and 5 using a connector block (or by soldering). Here is where your inline fuse holders will come into play. Wire a inline fuse holder to all 3 live feeds, and fit one with a 30amp fuse, one with a 20amp fuse and one with a 5 amp fuse. Wire the 20 amp feed to the Orange/White wire coming from Pin 2 of the driver's seat plug, the 30 amp feed to the Orange/Yellow wire coming from pin 4, and the 5amp feed to the Brown/Pink wire coming from Pin 5. Use my wiring diagram above to help you here.




Earth:
Pins 3 (Black wire) and 7 (Black/Slate) are the earth wires for the driver's seat electrics. Simply wire both of these to a suitable earth point in the car using a crimp ring connector, the closest one I found was in the drivers footwell under the carpet near the bonnet and boot release as shown below.



Pin 1:
The Yellow wire coming from Pin 1 of the seat plug is for the heated seat switch. Using your 5amp wire, connect this to Pin 2 of the driver's heated seat switch plug. You can feed the wire via the same route to the centre consol that was used for the power wire explained above.



Pin 6: (K-Bus)
This step is optional and only relevant if you have memory seats and if you wish to have the memory function working. If you wish to wire this up, you will need to find the k-bus for the radio behind the centre console (red, white and yellow wire) connect into it.

Your driver's side loom will look like this:


Wiring up the Passenger's Seat:
This one is a little easier than the Drivers seat as there are less wires and no K-Bus wire. The steps are the same as for the drivers seat wiring above.

Power:
For the passenger seat, you will need to split your live power feed into two and wire in your inline fuse holders. One fuse holder will require a 20amp fuse and the other will require a 5 amp fuse. As above, the 20amp live feed is to be wired to pin 2 (orange/white) wire of the electric seat plug, and the 5amp feed is to be wired to pin 5 (Brown/Pink) wire of the plug.

Earth:
There is only one earth for the passenger seat which is pin 3 (Black wire). As above for the driver's seat, wire this to a suitable earth point in the car using a crimp ring connector. the closest one I found for the passenger seat was under the carpet on the left side of the passenger footwell.

Pin 1:
As above for the driver seat, the Yellow wire coming from Pin 1 of the seat plug is for the heated seat switch. Using your 5amp wire, connect this to Pin 2 of the Passenger's heated seat switch plug.

Your passenger side loom will look like this:



Wiring up the Heated Seat Switches:

The heated seat switch plugs which fit in the centre consol each have the same 4 wires:

Pin 1 (Black) 1.5mm wire: this is the earth for the switch, simply wire to a suitable earth or if you have a spare unused switch plug behind the centre consol (such as the traction control plug), tap into the earth wire on that plug as it is unused.

Pin 2 (Yellow) 0.75mm wire: This is already done, as this is the wire which connects to pin 1 of the 8 pin electric seat plugs as dealt with above.

Pin 3 (Red/White) 0.5mm wire: This wire is for the illumination of the heated seat switch when you switch your lights on at night. Simply tap into another red and white wire behind the centre consol by soldering or using an electrical connector block.

Pin 4 (Orange/White) 0.5mm wire: this is for the green light which illuminates when the heated seat switch is on, this will need to be wired to another 12v switched feed (only live when the ignition is on). I wired this to an ignition live red/white wire behind the centre consol for the traction control switch which is not used. If you have the earlier ciggy lighter which is ignition live, you could tap into this or use the power feed for your seats as explained here: http://www.the75andztclub.co.uk/foru...42&postcount=5





And that's it:
Now plug in your electric seats and heated seat switches, reconnect the battery and test all the functions to ensure they work. Remember to have the key turned in the ignition to test the heated seats. I'd advise testing before putting all your interior back together just incase something doesn't work, meaning you'll have to check the wiring. I made my wiring under the seats long enough so that I could test them before fitting them in the car...



Other useful guides:
http://www.the75andztclub.co.uk/foru...ad.php?t=15926
https://www.the75andztclub.co.uk/forum/showpost.php?p=1020242&postcount=5

Hope this helps anyone looking to fit electric seats to a 75 or ZT which doesn't have the eelctric seats loom in place.

Usual Disclaimer applies:
You are responsible for any work or modifications carried out on your car and you undertake any such work at your own risk.
The 75 and ZT Owners Club nor the original author of this How-To can be held liable for anything that may happen as a result
of you following this How-To.
thanks so much... your "1 day task" will most likelly be "my week" Great stuff
ALBLOHE is offline   Reply With Quote
Old 10th February 2017, 22:46   #27
Rick-sta
This is my second home
 
Rick-sta's Avatar
 
MG ZT 2.0 CDTI+ in Typhoon, MG TF 135 in Typhoon & Rover 75 Connoisseur CDTI SE in Pearl Black

Join Date: Oct 2012
Location: Norfolk
Posts: 7,523
Thanks: 2,718
Thanked 2,827 Times in 1,462 Posts
Default

Quote:
Originally Posted by ALBLOHE View Post
thanks so much... your "1 day task" will most likelly be "my week" Great stuff
no problem it's not too bad to do, much easier than trying to extract an original factory loom from another car and then fitting it to your own
__________________
How to retrofit Cruise Control on a diesel with no OEM wiring in place: Link
How to retrofit heated electric memory seats with no OEM wiring in place: Link
How to operate FBH and ATC via text Link
How to restore cloudy projector headlights Link
Rick-sta is offline   Reply With Quote
Old 18th February 2017, 16:53   #28
lynch1d
Newbie
 
lynch1d's Avatar
 
mg zt

Join Date: Dec 2016
Location: Sunderland
Posts: 20
Thanks: 1
Thanked 1 Time in 1 Post
Default

wired up my seats, they work great thanks, but the connectors for the airbag were different so i had to cut the old connector off and wire in the new one ,now i have an airbag fault warning light on my dash any advice would be appreciated
lynch1d is offline   Reply With Quote
Old 18th February 2017, 19:41   #29
Rick-sta
This is my second home
 
Rick-sta's Avatar
 
MG ZT 2.0 CDTI+ in Typhoon, MG TF 135 in Typhoon & Rover 75 Connoisseur CDTI SE in Pearl Black

Join Date: Oct 2012
Location: Norfolk
Posts: 7,523
Thanks: 2,718
Thanked 2,827 Times in 1,462 Posts
Default

Quote:
Originally Posted by lynch1d View Post
wired up my seats, they work great thanks, but the connectors for the airbag were different so i had to cut the old connector off and wire in the new one ,now i have an airbag fault warning light on my dash any advice would be appreciated
the airbag connections changed on later cars so mki vs mkii airbag connectors are different. The airbag light is probably on due to one of the collections under the seats which you've had to wire in. Check the wiring there to make sure they all have good connections
__________________
How to retrofit Cruise Control on a diesel with no OEM wiring in place: Link
How to retrofit heated electric memory seats with no OEM wiring in place: Link
How to operate FBH and ATC via text Link
How to restore cloudy projector headlights Link
Rick-sta is offline   Reply With Quote
Old 18th February 2017, 21:58   #30
lynch1d
Newbie
 
lynch1d's Avatar
 
mg zt

Join Date: Dec 2016
Location: Sunderland
Posts: 20
Thanks: 1
Thanked 1 Time in 1 Post
Default

thanks rick will do, might just bypass the connectors and hardwire them
lynch1d is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:59.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright © 2006-2023, The Rover 75 & MG ZT Owners Club Ltd