Starter Motor Bolt (CDTI)

daveo138 · 13th May 2022, 21:32

Browsing under the bonnet, as you do, and it looks like I might have a bolt (set screw) missing from the starter motor mounting (photo).

If this is correct, can anyone tell me the dimensions of the correct fastener?

Thanks.

Mike Noc · 13th May 2022, 22:19

There are two bolts holding the starter motor, and if I remember correctly there is a locating dowel. One bolt threads into the bellhousing and the other is secured by a nut.

daveo138 · 13th May 2022, 23:21

I can see the long bolt and nut, but I’m struggling to see a second one, so was wondering if that’s where it should be, or are you saying that that’s where the dowel is located?

Mike Noc · 13th May 2022, 23:49

It was a few years ago that I last had a starter motor off Dave, but from what I remember the second bolt is further round from your arrow, so you should be fine.

smudge.g · 14th May 2022, 08:11

Hi, having just done a starter removal, the 2nd bolt (top) is further back and has an earth lead attached to it, which runs across under some ducting to near the battery box. You may have to move a few leads out of the way to be able to see it. I found it easier t locate by looking down on the starter from further back if you have removed the engine cover/air ducting etc. Its a pig to remove that bolt if you have a FBH installed btw! good luck.

Mike Noc · 14th May 2022, 08:43

Last one I did was on an auto, and had to find the earthstrap bolt by feel and a long extension - far too much gubbins in the way to see it.

Arctic · 14th May 2022, 08:43

Hi Dave.
Mike & Gary are correct only to fixings one and bolt hidden behind some rubber ducting at the top and rear of starter, the other is a bolt and nut at the bottom, what you are seeing is the point for the dowel on the starter to line it up before fitting the bolts.

1

daveo138 · 14th May 2022, 18:53

Thanks all.

I can stop worrying now

14th May 2022, 08:11	#5
smudge.g Gets stuck in 75 Tourer CDTi Connie SE Join Date: Jun 2017 Location: Keith, Banffshire Posts: 635 Thanks: 426 Thanked 128 Times in 102 Posts	Hi, having just done a starter removal, the 2nd bolt (top) is further back and has an earth lead attached to it, which runs across under some ducting to near the battery box. You may have to move a few leads out of the way to be able to see it. I found it easier t locate by looking down on the starter from further back if you have removed the engine cover/air ducting etc. Its a pig to remove that bolt if you have a FBH installed btw! good luck. __________________ My 75 Tourer CDTi was born Saturday, 21st June 2003 @ 09:50 My 75 was the 18,749th 75 Tourer to run off the production line, out of 27,407 It was the 195th 75 Tourer CDT Connoisseur SE (135) to be made out of 2,074 and the 1,789th 75 Tourer in Wedgewood Blue Metallic (code: JEL) to be made out of 1,871 Wedgewood Blue Metallic 75 Tourers

14th May 2022, 08:43	#7
Arctic Give to Learn Rover 75 Tourer Join Date: Aug 2010 Location: West Midlands Posts: 16,599 Thanks: 1,031 Thanked 5,840 Times in 3,533 Posts	Hi Dave. Mike & Gary are correct only to fixings one and bolt hidden behind some rubber ducting at the top and rear of starter, the other is a bolt and nut at the bottom, what you are seeing is the point for the dowel on the starter to line it up before fitting the bolts. 1 __________________ Arctic Givology Learn to Give Everything is Achievable ad altiora tendo. Check out our Nano meet dates http://www.midlandsnanomeets.co.uk/ http://www.the75andztclub.co.uk/index.php?thepage=howto " You do the work , we supply the expertise "

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

13th May 2022, 22:19	#2
Mike Noc Relax, it's a Rover. Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4. Join Date: Jul 2009 Location: Hampshire Posts: 11,022 Thanks: 3,258 Thanked 2,991 Times in 2,158 Posts	There are two bolts holding the starter motor, and if I remember correctly there is a locating dowel. One bolt threads into the bellhousing and the other is secured by a nut.

13th May 2022, 23:21	#3
daveo138 Regular poster Rover 75 Tourer Join Date: Mar 2022 Location: Chesterfield Posts: 56 Thanks: 27 Thanked 6 Times in 5 Posts	I can see the long bolt and nut, but I’m struggling to see a second one, so was wondering if that’s where it should be, or are you saying that that’s where the dowel is located?

13th May 2022, 23:49	#4
Mike Noc Relax, it's a Rover. Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4. Join Date: Jul 2009 Location: Hampshire Posts: 11,022 Thanks: 3,258 Thanked 2,991 Times in 2,158 Posts	It was a few years ago that I last had a starter motor off Dave, but from what I remember the second bolt is further round from your arrow, so you should be fine.

14th May 2022, 18:53	#8
daveo138 Regular poster Rover 75 Tourer Join Date: Mar 2022 Location: Chesterfield Posts: 56 Thanks: 27 Thanked 6 Times in 5 Posts	Thanks all. I can stop worrying now