|
||
|
25th September 2018, 10:39 | #1 |
Posted a thing or two
MG ZT-T 190+,Rover 800 vitesse coupe Join Date: Aug 2014
Location: Hamilton
Posts: 1,969
Thanks: 616
Thanked 228 Times in 210 Posts
|
Alloy spare in tourer with surround tool storage
Hi all never had a spare wheel before only the tins of foam, so have one now admittedly it’s flat at the moment so how do you all get it to fit with the cover as even with it flat it keeps the moulded cover up and when I close the main cover it sits up proud ?
Thanks
__________________
Robert |
25th September 2018, 11:49 | #2 | |
Premium Trader
Rover 75 Join Date: Nov 2010
Location: Devon
Posts: 33,766
Thanks: 8,837
Thanked 14,831 Times in 8,030 Posts
|
Quote:
Send Ian G a message he has managed to do this, I’m sure he can explain what is needed.
__________________
Lest we forget..
|
|
25th September 2018, 14:31 | #3 |
Avid contributor
Rover 75 Tourer Join Date: Jan 2014
Location: St Helier
Posts: 113
Thanks: 144
Thanked 34 Times in 24 Posts
|
Must depend on the alloy. I have a Crown wheel and it fits no problem.
|
25th September 2018, 16:00 | #4 |
Posted a thing or two
MG ZT-T 190+,Rover 800 vitesse coupe Join Date: Aug 2014
Location: Hamilton
Posts: 1,969
Thanks: 616
Thanked 228 Times in 210 Posts
|
This is a straight I’m asking about if it makes a difference
__________________
Robert |
25th September 2018, 16:39 | #5 | |
This is my second home
Small Join Date: Feb 2010
Location: Land of the Eel
Posts: 6,315
Thanks: 2,328
Thanked 2,991 Times in 1,431 Posts
|
Quote:
They will fit but I needed to trim the top lip a little (20mm) to allow the load area floor to sit flush, thats with a full size spare wheel fitted with a 225 x 45 x 18 tyre. I'll take a couple of photos tomorrow and add to this thread. Cheers Ian |
|
29th September 2018, 19:38 | #6 |
Posted a thing or two
MG ZT-T 190+,Rover 800 vitesse coupe Join Date: Aug 2014
Location: Hamilton
Posts: 1,969
Thanks: 616
Thanked 228 Times in 210 Posts
|
Just a small bump to Ian G to see if you have had a chance with the photos ?
Thanks
__________________
Robert |
29th September 2018, 23:42 | #7 |
Gets stuck in
Rover 75 Tourer CDTi Join Date: Jun 2017
Location: Plymouth
Posts: 692
Thanks: 141
Thanked 153 Times in 117 Posts
|
I never had the carpeted tray in my tourer when I bought it.
I picked up a second hand tray and couldn't get the foam tool holder to fit properly on top of the tray under the boot floor. To sort the problem i got a saw and cut about 1.5 inches of foam of the lower side of the tool holder so it sat lower, it has been fine since |
30th September 2018, 11:58 | #8 | |
This is my second home
Small Join Date: Feb 2010
Location: Land of the Eel
Posts: 6,315
Thanks: 2,328
Thanked 2,991 Times in 1,431 Posts
|
Quote:
So a description will maybe help you.. You need to reduce the height of the verticle lip around the outside of the liner. Raise the floor and place the liner in position in the spare wheel then if you use a small straight edge from the load area floor at the side you will see approx how much you need to cut off, don't forget to allow for the thickness of the load area floor, I marked the cutting height with a marker pen then used a chalk line to mark the cut line. I used a 1mm cutting disc on a 4" angle grinder to make the cut. Hope this helps out. Cheers Ian Last edited by Ian G; 30th September 2018 at 12:37.. |
|
2nd October 2018, 07:35 | #9 |
Posted a thing or two
MG ZT-T 190+,Rover 800 vitesse coupe Join Date: Aug 2014
Location: Hamilton
Posts: 1,969
Thanks: 616
Thanked 228 Times in 210 Posts
|
Thanks Ian have had rain the last week so in no rush to work on it, only thing that goes in the boot is the dog so I’m okay for the lip to stay up in the short term
__________________
Robert |
|
|