|
||
|
26th March 2009, 16:34 | #1 |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
BW 17 Pin Connector
Following on from Les and his Sat Nav Problems, I need to dismantle the 17 pin connector.
I've got the BMW manual showing the tool, but I can't work out if it slides over the pin or goes inside the pin to release in from the housing. Any suggestions ?
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
27th March 2009, 15:49 | #2 |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
ah come on, someone must know....
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
27th March 2009, 17:19 | #3 |
Avid contributor
rover 75 2.5 V6 auto Join Date: Feb 2008
Location: Alkmaar
Posts: 197
Thanks: 0
Thanked 3 Times in 3 Posts
|
Have look here:
http://m3.madrussian.net/diy_ipod.shtml This guy gives an ID of 4.00mm and OD 4.25mm so it must go over the pin. Hans |
27th March 2009, 20:14 | #4 |
Gets stuck in
Ex Rover 75 owner Join Date: Nov 2006
Location: Boston, Lincolnshire.
Posts: 553
Thanks: 0
Thanked 2 Times in 2 Posts
|
It must go over the pin to pull in the barbs thus allowing you to remove it.
According to the thread above.
__________________
Regards Andrew.[SIGPIC][/SIGPIC] |
27th March 2009, 20:25 | #5 |
Loves to post
Rover 75 saloon club SE manual 2.0 V6 Join Date: May 2008
Location: Chatham, Kent.
Posts: 289
Thanks: 0
Thanked 0 Times in 0 Posts
|
The female ones just slide down the outside. Supposed to just push out, did couple on mine, bit of a pig to get out. Lot of wiggling and jiggling.
__________________
[SIGPIC][/SIGPIC] |
27th March 2009, 20:37 | #6 |
*
Rover 75 FaceLift Tourer CDTi 170BHP Auto ConnSE 2005 Model Starlight Silver Join Date: Nov 2006
Location: Abergele
Posts: 28,735
Thanks: 0
Thanked 6 Times in 5 Posts
|
Les not got any old Looms there David?
|
27th March 2009, 20:39 | #7 |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
The connector in Les's boot is very manky and broken so that's 17 to take out, plus the 17 to take out of the connector I salvaged.
At least with the dimensions, I can try and get a tool made up....
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
27th March 2009, 20:41 | #8 |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
It's the connector that goes into the tuner in the wheel well...I've got the connector off another car, just can't get the pins out to change it....
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
27th March 2009, 21:09 | #9 |
This is my second home
Jaguar XE Join Date: Nov 2006
Location: Coventry
Posts: 4,321
Thanks: 56
Thanked 59 Times in 55 Posts
|
Soldering iron,side cutters and heat shrink
Joking apart you can buy the tool for "de barbing" the connectors.Failing using the correct tool, use a safety pin and a jiggle should sort it. |
28th March 2009, 07:58 | #10 | |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
Quote:
Tried the pin trick, but alas no joy. Might pop into BMW to get the price of the tool...
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
|
|
|