Drivers window- one touch

MGtom91 · 15th June 2021, 19:41

Drivers window one touch down working. Activated one touch up in toaf but then the window doesn't go up (have to keep pressing the switch on and off as window moves up a few mm at a time and when switch Is held moves a few mm then stops). Turn off one touch up in toaf and you can hold the switch and window goes all the way up manually but just not one touch.

Is there a reset procedure or is something faulty?

slovcan · 16th June 2021, 11:16

Quote:

Originally Posted by MGtom91

Drivers window one touch down working. Activated one touch up in toaf but then the window doesn't go up (have to keep pressing the switch on and off as window moves up a few mm at a time and when switch Is held moves a few mm then stops). Turn off one touch up in toaf and you can hold the switch and window goes all the way up manually but just not one touch.

Is there a reset procedure or is something faulty?

I suspect there is something wonky with the pinch sensor in (or under?) the top window channel weatherstrip. Sorry, I can't tell you which connector it is (hopefully another fellow here with experience can say), but I would open that connector and make sure the contacts are clean and tight - as a first step.

SKS Disco · 16th June 2021, 12:36

Quote:

Originally Posted by MGtom91

Drivers window one touch down working. Activated one touch up in toaf but then the window doesn't go up (have to keep pressing the switch on and off as window moves up a few mm at a time and when switch Is held moves a few mm then stops). Turn off one touch up in toaf and you can hold the switch and window goes all the way up manually but just not one touch.

Is there a reset procedure or is something faulty?

Is this something you have added or did they used to work?
If recently added I would suspect " One shot up" and "One shot up anti trap" is not activated in the ZCS coding string.

clf · 16th June 2021, 12:45

Go back to toaf and check pinch is off. I seem to recall a similar issue, I'm trying to activate one shot on the passenger side. It made all the windows go into pinch mode as the bcu (I assume) was looking for the non existent sensor.

It has been a while, but i think if you uncheck all the modes, it will set it back to default.

Sent from my SM-A600FN using Tapatalk

MGtom91 · 16th June 2021, 13:08

I seem to recall it happened around the time I turned off deadlocking in toaf. Have read it can cause some issues with other settings. So make sure close by pinch is deactivated? Anything else to check or uncheck on there that would affect one touch up?

clf · 16th June 2021, 18:18

Quote:

Originally Posted by MGtom91

I seem to recall it happened around the time I turned off deadlocking in toaf. Have read it can cause some issues with other settings. So make sure close by pinch is deactivated? Anything else to check or uncheck on there that would affect one touch up?

I cannot recall to be honest. But I did check the one touch close on the passenger, and it immediately went to pinch mode. If I recall also, the drivers side did too, but I didnt touch it.

My first use of TOAF caused an issue with the remote release, without me even opening that module! I had to go into it and uncheck the tailgate release (which had checked itself) and leave the boot/trunk release ticked. My car is a saloon, and the both tailgate and boot release were simultaneously checked.

There are known to be bugs around TOAF, I suspect that that it has something to do with it being derived on BMW software (whose cars would have antitrap on all windows compared to ours on the drivers door). It is good enough though, but back everything up, be cautious, and if you are unsure, avoid using it.

COLVERT · 16th June 2021, 19:29

A very remote chance but you never know.---Disconnect the battery negative terminal for half an hour. Miracles can sometimes happen.---

clf · 16th June 2021, 20:15

Quote:

Originally Posted by COLVERT

A very remote chance but you never know.---Disconnect the battery negative terminal for half an hour. Miracles can sometimes happen.---

plus one for this too (the mention of TOAF always sends me in that direction though from experience lol)

joel antonio · 17th June 2021, 07:26

Hi Tom:

I have the same problem right now.

I'm going to check this weekend to see if I can get it working properly again.

If not I will make a backup of my other Rover that is working properly and restore it to see what happens.

On the other hand, the miracle of the disconnected battery did not work for me.

Kind regards
Joel Antonio

MGtom91 · 17th June 2021, 09:00

These cars keep you busy! So in toaf, close by pinch was active. After turning off, the window now goes up all the way when holding the switch but still no one touch up, even though activated in toaf. Have left battery off overnight and will reconnect and test later. Unfortunately, I did not take a backup so I cannot restore

15th June 2021, 19:41	#1
MGtom91 Regular poster MG ZT KV6 (160) Join Date: Feb 2018 Location: Solihull Posts: 36 Thanks: 0 Thanked 6 Times in 6 Posts	Drivers window- one touch Drivers window one touch down working. Activated one touch up in toaf but then the window doesn't go up (have to keep pressing the switch on and off as window moves up a few mm at a time and when switch Is held moves a few mm then stops). Turn off one touch up in toaf and you can hold the switch and window goes all the way up manually but just not one touch. Is there a reset procedure or is something faulty?

16th June 2021, 12:45	#4
clf This is my second home MG ZT CDTi Join Date: Jan 2014 Location: carrick Posts: 7,859 Thanks: 3,494 Thanked 2,657 Times in 1,973 Posts	Go back to toaf and check pinch is off. I seem to recall a similar issue, I'm trying to activate one shot on the passenger side. It made all the windows go into pinch mode as the bcu (I assume) was looking for the non existent sensor. It has been a while, but i think if you uncheck all the modes, it will set it back to default. Sent from my SM-A600FN using Tapatalk __________________ It is not gloss primer .............. it is duct tape silver!

17th June 2021, 07:26	#9
joel antonio Avid contributor 2003 Rover 75 Tourer Club 2.5 auto, 2000 Rover 75 Club 2.5 manual, 2002 Connoisseur SE 2.5 Auto Join Date: Feb 2011 Location: Segovia, Spain Posts: 170 Thanks: 127 Thanked 28 Times in 21 Posts	Same happens to me... Hi Tom: I have the same problem right now. I'm going to check this weekend to see if I can get it working properly again. If not I will make a backup of my other Rover that is working properly and restore it to see what happens. On the other hand, the miracle of the disconnected battery did not work for me. Kind regards Joel Antonio __________________ My three amigos...!!!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

16th June 2021, 13:08	#5
MGtom91 Regular poster MG ZT KV6 (160) Join Date: Feb 2018 Location: Solihull Posts: 36 Thanks: 0 Thanked 6 Times in 6 Posts	I seem to recall it happened around the time I turned off deadlocking in toaf. Have read it can cause some issues with other settings. So make sure close by pinch is deactivated? Anything else to check or uncheck on there that would affect one touch up?

16th June 2021, 19:29	#7
COLVERT This is my second home R75 Saloon. Join Date: Feb 2009 Location: France/or Devon. Posts: 14,003 Thanks: 3,851 Thanked 2,167 Times in 1,816 Posts	A very remote chance but you never know.---Disconnect the battery negative terminal for half an hour. Miracles can sometimes happen.---

17th June 2021, 09:00	#10
MGtom91 Regular poster MG ZT KV6 (160) Join Date: Feb 2018 Location: Solihull Posts: 36 Thanks: 0 Thanked 6 Times in 6 Posts	These cars keep you busy! So in toaf, close by pinch was active. After turning off, the window now goes up all the way when holding the switch but still no one touch up, even though activated in toaf. Have left battery off overnight and will reconnect and test later. Unfortunately, I did not take a backup so I cannot restore