|
||
|
22nd February 2011, 20:58 | #1 |
Newbie
MG-ZT 190 Join Date: Feb 2011
Location: Gibraltar
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
Help pls: Correct colour wiring for highline radio unit - parrot
Dear all,
I really hope someone can help me with this. I have already searched for hours, but I didn't find the correct answer. Sometime ago my radio broke down due to a water damage and when the mechanic unpluged the radio he destroyed the wiring loom. That is why some electric cables are now torn apart from the parrot adaptor and they have no documentation in the garage on how to rewire this again. Basically I need the colour code of a highline radio unit (satnav Tv radio) for a MG-ZT 190 which I have (I think rover 75 owners could also help) The simplest would be if someone could just upload a picture of their radio-wiring parrot in the boot. The adaptor looks like this: (this is an old adaptor, round pins.) My replacement radio is a BM24 because I could not find the original XQC000240. The colous I have on the broken parrot adaptor are the following: Pin1 - white-black Pin2 - violet-black Pin3 - brown-black Pin4 - ? Pin5 - green-white Pin6 - green black Pin7 - ? Pin8 - grey-black Pin9 - ? Pin10 - empty Pin11 - blue-black Pin12 - red-black Pin13 - empty Pin14 - orange-black Pin15 - black (a bigger cable) Pin16 - yellow--violet Pin17 - empty The 3 loose cables are: violet-white(or bright pink) bright yellow-red red-green Can anyone tell me to which of the above numbers with the question mark they correspond? THANK YOU VERY MUCH mic165 |
23rd February 2011, 08:21 | #2 |
Newbie
MG-ZT 190 Join Date: Feb 2011
Location: Gibraltar
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
Maybe it makes more sense if this thread is in the I.C.E. highline section of the forum.
Can an admin please move it there?...thx |
23rd February 2011, 09:54 | #3 |
Owners Club Director
Rover 75 Conn SE V6 / MG ZT 260 SE V8 / MG ZT 180 SE V6 Join Date: Feb 2007
Location: Southampton
Posts: 20,943
Thanks: 645
Thanked 6,851 Times in 2,537 Posts
|
Done ...........
|
24th February 2011, 14:23 | #4 |
Owners Club Director
Rover 75 Conn SE V6 / MG ZT 260 SE V8 / MG ZT 180 SE V6 Join Date: Feb 2007
Location: Southampton
Posts: 20,943
Thanks: 645
Thanked 6,851 Times in 2,537 Posts
|
O.K, I've had a chance to look at my set-up and the notes I made when installing it taken from the workshop manual, and it's as follows:
Pin1 - white-black - (Speaker Left Front +) Pin2 - violet-black - (Speaker Right Front +) Pin3 - brown-black - (Speaker Left Rear +) Pin4 - ? Red-Green - (Telephone Mute signal) Pin5 - green-white - (Ignition Switch Power Supply) Pin6 - green black - (Speaker Right Rear +) Pin7 - ? White-Red-Yellow - (K Bus Connection) Pin8 - grey-black - (Speaker Left Front -) Pin9 - ? Purple-Pink (Battery Permanent Feed) Pin10 - empty (Speed dependant Volume Signal - N/A) Pin11 - blue-black - (Speaker Right Front -) Pin12 - red-black - (Speaker Left Rear -) Pin13 - empty - Not Used Pin14 - orange-black - (Speaker Right Rear -) Pin15 - black (a bigger cable) - (Earth) Pin16 - yellow--violet - (Aerial Amplifier Switching Signal) Pin17 - empty - Not Used Hope that helps. |
|
|