|
||
|
12th October 2020, 07:01 | #1 |
Regular poster
MG ZT Join Date: Jun 2012
Location: Plymouth
Posts: 51
Thanks: 26
Thanked 4 Times in 4 Posts
|
National clutches fail within 4000 miles
Hi all,
Andy Willi is apparently up and running again although I am struggling to reach him. He did both my ZTT and my ZT in prep for Philt4s map. Unfortunately both clutches failed within 4000 miles, in fact my ZT barely covered 2000 I think. I came across a post from late 2018 naming and shaming a customer of his for having work done and never paying. In the same vein I can’t help but feel if he’s working again that he should honour the work carried out that was clearly sub standard. I’m not saying it was his fault, National clutches may have had a bad batch for example. I had already taken a trip from Plymouth to Doncaster and back to have the ZTTs clutch re looked at and sold it a couple of months later as I felt it wasn’t right but thought it might just be in my head. I later had a message from the chap calling me a tw*t for selling him a car with a dodgy clutch. Not long after, despite having the wheels and body resprayed and a host of mods done I found it scrapped. I still have my ZT on the driveway begging for the clutch to be redone. I got hold of Andy ages ago but suddenly he stopped communicating with me. Do I have any recourse? Does anyone know how to get hold of him? I left him to it, sympathising with his situation but apparently he’s back fitting and repairing so I absolutely believe he should honour the work that has failed so quickly. Between the two cars and the drive to Doncaster I spent over £1100 What do you think? Apologies in advance if this is not the correct area to seek advice. |
12th October 2020, 08:54 | #2 |
This is my second home
MG ZT260 SE, MG ZT190+, MG ZTT 160, R75 Conn SE 2.0, R75 Conn SE 2.5 X 3, R75 Club SE 1.8, P5B Coupe Join Date: Jul 2009
Location: Keynsham, Bristol
Posts: 4,211
Thanks: 65
Thanked 635 Times in 499 Posts
|
I feel for you.
Had you been a customer of mine, I would have rectified this asap but then, I would never have fitted a National brand of clutch! I'll only fit LUK, Sachs, AP/Borg & Beck clutches. As for any recourse now, it may be a little too late & I can only speak for myself regarding honouring warranties. I do hope you get this sorted though. |
12th October 2020, 12:58 | #3 |
Discount MG Rover Spares
Rover 75 CDTi, 2x MG ZS180 Join Date: Jun 2011
Location: Hythe, Southampton
Posts: 11,320
Thanks: 456
Thanked 3,377 Times in 2,027 Posts
|
What kind of timescale are we talking? I might have mis-read the post, though!
__________________
Your trusted MG Rover specialist! Tel: 02380 001133 / Email: [email protected] We now have a 'chat' function on our site for even quicker replies. Give it a try! Remember - discount code FORUM5 for 5% off |
12th October 2020, 13:14 | #4 |
Give to Learn
Freelander 2 Join Date: Aug 2010
Location: West Midlands
Posts: 18,717
Thanks: 1,155
Thanked 6,407 Times in 3,874 Posts
|
Do the right thing.
Zach another £200 and you could of had both the clutches & master And slaves done at the place i had both my MGZT, and my Freelander done 2yrs warranty or 18,000 miles which ever comes first no questions asked replacement, i think i told you this at the time while you were at the Nano.
I also feel a little bad as at the same time i suggested contacting Andy, we all know in life we live and learn, also looking back if i remember at the time it was about cost, as you were on a budget then, therefore my suggestion and also at the time it was not known what clutches he was using, but we do now :em: i think you know me well enough if it had been known i would never have suggested to try him, hopefully he will step up to the plate and sort something out with you.
__________________
Arctic Givology Learn to Give Everything is Achievable ad altiora tendo. Check out our Nano meet dates http://www.midlandsnanomeets.co.uk/ http://www.the75andztclub.co.uk/index.php?thepage=howto " You do the work , we supply the expertise " |
12th October 2020, 13:30 | #5 |
Gets stuck in
MGZTT Join Date: Feb 2015
Location: Bradford
Posts: 529
Thanks: 148
Thanked 256 Times in 138 Posts
|
What has failed, is it the clutch itself or the hydraulic side? I ask this because you will find a large number of posts regarding this issue on this site.
I had an LUK clutch go on my ZT-T, the master failed after 13 months and 3000 miles, and again on the slave a further 11 months later. Not covered by warranty, over 12 months, and not fitted by Andy Willy but Trikey who I do not blame at all. Replacement clutches are notorious now for failures like this and it doesn't seem to matter whose you buy. Even the Tazu have failed prematurely. Big Russ has told me that customers of his have had this happen and in some cases repeatedly, so he advisors anyone wanting a 75/ZT to always go for an auto and avoid the manuals. |
12th October 2020, 14:54 | #6 | |
Regular poster
MG ZT Join Date: Jun 2012
Location: Plymouth
Posts: 51
Thanks: 26
Thanked 4 Times in 4 Posts
|
Quote:
The ZT initially suffered a failed Tazu slave but slippage was always an issue from the National clutch. |
|
12th October 2020, 15:17 | #7 | |
Regular poster
MG ZT Join Date: Jun 2012
Location: Plymouth
Posts: 51
Thanks: 26
Thanked 4 Times in 4 Posts
|
Quote:
Andy seemed a stellar chap, fingers crossed he’ll get in touch. Cheers |
|
12th October 2020, 15:51 | #8 |
This is my second home
MG ZT and Rover 75, Join Date: Jul 2013
Location: Wigan
Posts: 3,276
Thanks: 2,556
Thanked 2,685 Times in 1,037 Posts
|
Not good service.
A few years ago when I found out what was being charged for a clutch swap I posted that it seemed expensive, I then had a load of members telling me how wrong I was but, he later admitted that he was using National clutches and Marina Brian did some digging on costs, if you ordered a set amount the price was as low as £35. It then became obvious that over £100 per hour was being made in labour charges for fitting cheap parts. I wouldn't fit one to my cars and spent £200 on an LUK one with a genuine Rover slave, it's not about anything other than making a maximum amount of money. Do you think you'll get the job redone at his expense with a better quality clutch? I'll take a wild guess at no and that's enough of a lesson for any member to learn, you don't always get what you pay for. The best thing you can do is buy your own clutch and pay for a proper job with one of the traders found on here.
|
12th October 2020, 15:55 | #9 |
Owners Club Director
Rover 75 Conn SE V6 / MG ZT 260 SE V8 / MG ZT 180 SE V6 Join Date: Feb 2007
Location: Southampton
Posts: 20,941
Thanks: 645
Thanked 6,851 Times in 2,537 Posts
|
Andy has yet to confirm to any of the club officials that he's working on clutch replacements again, and indeed is still just a regional secretary on here not a trader as before.
I would suggest you contact actros who it was that announced andy's return to ask Andy Willi to get in touch with you again regarding this outstanding issue you have. Clearly there is a good line of communication between the two of them. For what it's worth (and it might not be much) the National Clutch and LUK slave cylinder Andy fitted to my ZT-T on 11th of January 2015 is still working perfectly on my car with it having covered an additional 27,783 miles so far. I can only speak as I find. |
12th October 2020, 17:58 | #10 | |
Regular poster
MG ZT Join Date: Jun 2012
Location: Plymouth
Posts: 51
Thanks: 26
Thanked 4 Times in 4 Posts
|
Quote:
Hmmm. I’m not sure it’s a good idea to condemn all manual ZTs/75s, better perhaps to take the manufacturers to task and resolve the issue. DMGRS are still making a portion of their living supplying parts for and fitting manual clutches are they not? They must still be confident in the process. As I mentioned in my post, I’m not blaming as such, he could have been unlucky with a range of bad parts. However, as the point of advise, purchase and fitment, there’s a responsibility to be reachable, to offer a degree of after sales service, to liaise with the companies that won’t liaise with you, as you were not the buyer of the product. Last edited by Zeeblum; 12th October 2020 at 18:04.. |
|
|
|