|
||
|
30th November 2021, 06:57 | #21 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,338
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Quote:
Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
|
30th November 2021, 11:30 | #22 |
Loves to post
MG ZT-T CDTi Join Date: Sep 2020
Location: Lincs
Posts: 288
Thanks: 73
Thanked 51 Times in 44 Posts
|
Guys.
I dont plan to remove the roll bar and yeah no scaffolding tube also hate getting into secondary faults like that so only if absolutely necessary...... Always managed to get the bolts tight but not with a torque wrench just as tight as they will go with a single push using my foot at the end just enough so i can get them off again one day lol. The problem i had with this side last time is getting the bush bolts started straight it took a second set of hands to manipulate the bush to prevent it pulling the bolts off centre. Last time i mashed the threads in the sub frame so do have the right tap on hand if needed but I havent get that far today. Bit annoyed with Rimmers sending me a bush that ripped itself apart as to tight to fit onto the arm... Last two times the bush has pressed on nicely using loads of washing up liquid and my significant weight on it. NOT THIS TIME Im trying to calm down before contacting Rimmers...
__________________
ZT-T Mk2 Jobs to do: Renew auxiliary drive belt # Replace driver door lock actuator # Refurbish wheels Last edited by Retap; 30th November 2021 at 12:22.. |
30th November 2021, 12:36 | #23 |
This is my second home
Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4. Join Date: Jul 2009
Location: Hampshire
Posts: 11,547
Thanks: 3,470
Thanked 3,119 Times in 2,247 Posts
|
I use a small G clamp to gently hold the bush housing flat against the subframe, then with a small mirror above the hole tap the housing into place. Once the first bolt is in but not tight remove the G clamp, align the second hole and bolt it up.
|
30th November 2021, 13:08 | #24 | |
Loves to post
MG ZT-T CDTi Join Date: Sep 2020
Location: Lincs
Posts: 288
Thanks: 73
Thanked 51 Times in 44 Posts
|
Quote:
The last time i did this it was 30C middle of summer heatwave, i think i was struggling with that at the time and just feel things will go better this time if i can just get a bush on the arm lol. Last time i couldnt find a way to get the Gclamp to stay put but got mirror and clamp ready, will find the way once i get a bush that will go on the arm without ripping itself to pieces. Knew it was to tight today couldnt even get it started easy on the edge of the arm with smaller radius. Another day lost..... happy thought is still got 7 working days to get done for MOT retest. challenge accepted lol
__________________
ZT-T Mk2 Jobs to do: Renew auxiliary drive belt # Replace driver door lock actuator # Refurbish wheels |
|
30th November 2021, 14:00 | #25 |
Loves to post
MG ZT-T CDTi Join Date: Sep 2020
Location: Lincs
Posts: 288
Thanks: 73
Thanked 51 Times in 44 Posts
|
Good god now i got Rimmers asking for VIN code to ensure they sent the right bush lol yes its right handed as it should be but to tight to press on As far as i know there is only two types of lower arm bush available for our cars, right handed and left handed....
__________________
ZT-T Mk2 Jobs to do: Renew auxiliary drive belt # Replace driver door lock actuator # Refurbish wheels |
30th November 2021, 14:57 | #26 |
This is my second home
Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4. Join Date: Jul 2009
Location: Hampshire
Posts: 11,547
Thanks: 3,470
Thanked 3,119 Times in 2,247 Posts
|
If I remember I G clamped over the rear bolt hole and fitted the front bolt. Had the G clamp tight enough to hold the housing in place but loose enough to be able to move it with a hammer.
|
30th November 2021, 15:01 | #27 | |
Loves to post
MG ZT-T CDTi Join Date: Sep 2020
Location: Lincs
Posts: 288
Thanks: 73
Thanked 51 Times in 44 Posts
|
Quote:
ok cheers i will try that approach.
__________________
ZT-T Mk2 Jobs to do: Renew auxiliary drive belt # Replace driver door lock actuator # Refurbish wheels |
|
30th November 2021, 15:04 | #28 |
Loves to post
MG ZT-T CDTi Join Date: Sep 2020
Location: Lincs
Posts: 288
Thanks: 73
Thanked 51 Times in 44 Posts
|
Hats off to Rimmers they have dispatched a replacement bush at no cost and little fuss. I have a found a small variance on the arm using my eyes and a caliper. where the bush is supposed to sit it seems to be almost 28mm but on the edge its 29mm so i got little filing to do maybe.
Ordered another moog bush as well they seem to go on alright but might not last however needs must got to draw an end to this saga lol.
__________________
ZT-T Mk2 Jobs to do: Renew auxiliary drive belt # Replace driver door lock actuator # Refurbish wheels |
30th November 2021, 15:45 | #29 |
Loves to post
MG ZT-T CDTi Join Date: Sep 2020
Location: Lincs
Posts: 288
Thanks: 73
Thanked 51 Times in 44 Posts
|
Puller porn
The pullers I ordered but no longer need arrived so heres some puller porn to entertain whilst the bushes arrive.
The cheapo set I shall keep though not needed at present now however the Sealey has to go back sadly. Note the size differences side by side, the cheapo set has 2" and 3" plates whilst the sealey is bigger still maybe helpful to know one day lol.
__________________
ZT-T Mk2 Jobs to do: Renew auxiliary drive belt # Replace driver door lock actuator # Refurbish wheels |
1st December 2021, 11:32 | #30 |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
John.
I don't know if you know this and I found out by accident.----The housing with the bush in it has a hole through the casting.--It is very easy to put a nail bar through this hole to rotate the housing.--I put a scissors jack under the end of the nail bar to keep the housing flat against the car chassis. Sounds complicated but in fact it's very easy and quick to do. Much better than trying to fit a G clamp around the odd shaped housing. I then used a small mirror on a telescopic handle to look down the bolt holes to position the arm.--Lubricate the rubber bush well with liquid soap so it can be slid along to the correct position.--This is very important.-- Small mirrors on sticks.--Lidl's. Always handy to have. |
Thread Tools | |
Display Modes | |
|
|