|
||
|
5th June 2019, 09:24 | #11 |
This is my second home
Rover 75 cdt club + Rover 2.5 KV6 Conni SE Join Date: May 2008
Location: Birmingham
Posts: 11,392
Thanks: 6,587
Thanked 2,262 Times in 1,729 Posts
|
Yes that’s the full spoiler that fits on the top of the bootlid.Mine, which is away for spraying in GMN, seems to have the one that is missing on yours, further towards the back end,I.E.,further from the bolt that is still stuck in the spoiler. I might be wrong because as I said, it is away for spraying. When I undid the two domed nut’s, and the two screws on mine, they were only nipped up, not tightend down hard. I had more trouble getting it off the sticky gasket, so be careful when you are tightening them up or you may pull them through again.
__________________
Great Barr, Birmingham. |
5th June 2019, 09:44 | #12 |
This is my second home
rover 75 1.8 vvc club se wedgwood blue Join Date: Aug 2009
Location: Seaton Carew
Posts: 26,918
Thanks: 65
Thanked 7,142 Times in 4,642 Posts
|
Inside the hole should be a captive thread, any bolt that fits will do. It's located under the rubber buffers
Last edited by suzublu; 5th June 2019 at 11:55.. |
5th June 2019, 09:47 | #13 | |
Avid contributor
MG ZT-T (black Pearl) & Orange MG ZT-T Auto (Grove) Join Date: Apr 2019
Location: ipswich
Posts: 193
Thanks: 108
Thanked 53 Times in 34 Posts
|
Quote:
|
|
5th June 2019, 12:18 | #14 |
Avid contributor
MG ZT-T (black Pearl) & Orange MG ZT-T Auto (Grove) Join Date: Apr 2019
Location: ipswich
Posts: 193
Thanks: 108
Thanked 53 Times in 34 Posts
|
|
5th June 2019, 16:05 | #15 |
This is my second home
Rover 75 cdt club + Rover 2.5 KV6 Conni SE Join Date: May 2008
Location: Birmingham
Posts: 11,392
Thanks: 6,587
Thanked 2,262 Times in 1,729 Posts
|
They are 30ml long, the same thread as the domed nuts that you have. They have a small Allen key socket in the head, but as above any one will do 30ml long. Again, only tighten them up slightly onto the double sided sticky gasket that fits between the spoiler and bootlid.
__________________
Great Barr, Birmingham. |
5th June 2019, 16:48 | #16 | ||
Avid contributor
MG ZT-T (black Pearl) & Orange MG ZT-T Auto (Grove) Join Date: Apr 2019
Location: ipswich
Posts: 193
Thanks: 108
Thanked 53 Times in 34 Posts
|
Quote:
Quote:
|
||
5th June 2019, 17:45 | #17 | |
Gets stuck in
75 Tourer CDT MK2 manual in Glorious Grey Join Date: Jan 2018
Location: Slovakia
Posts: 987
Thanks: 926
Thanked 346 Times in 252 Posts
|
Quote:
Cheers, Glenn
__________________
Southern Slovakia Anything can happen in Formula 1 and usually does - Murray Walker 1999 Triumph Trophy 900, Saddlesore 1600, Iron Butt Riders Association #63720 2005 Rover 75 CDT Tourer MK2 |
|
5th June 2019, 21:07 | #18 |
This is my second home
Rover 75 cdt club + Rover 2.5 KV6 Conni SE Join Date: May 2008
Location: Birmingham
Posts: 11,392
Thanks: 6,587
Thanked 2,262 Times in 1,729 Posts
|
My screws fit into the domed nuts,so same size.
__________________
Great Barr, Birmingham. |
6th June 2019, 06:33 | #19 |
Avid contributor
MG ZT-T (black Pearl) & Orange MG ZT-T Auto (Grove) Join Date: Apr 2019
Location: ipswich
Posts: 193
Thanks: 108
Thanked 53 Times in 34 Posts
|
here's the confusion with my spoiler
here's the domed nut and a m10 thread side by side for my setup i've ordered some nylon bolts m10 x 25mm i think they should be fine... thanks all for your help.. much love |
6th June 2019, 22:04 | #20 |
This is my second home
Rover 75 cdt club + Rover 2.5 KV6 Conni SE Join Date: May 2008
Location: Birmingham
Posts: 11,392
Thanks: 6,587
Thanked 2,262 Times in 1,729 Posts
|
Yes. I can see that a larger size has been used. You will have to drill the hole for the new bolt larger, because the original ones are the same size according to mine.
__________________
Great Barr, Birmingham. |
|
|