|
||
|
28th May 2021, 15:42 | #1 |
Posted a thing or two
MGB GT, 2 Morris Minor Travellers Join Date: May 2011
Location: Bilston
Posts: 1,661
Thanks: 1,610
Thanked 497 Times in 370 Posts
|
Trailing arm adjustment bolts
Are the trailing arm adjustment bolts prone to shearing off when trying to undo them?
I wanted my car 4 wheel alignment attempted but they were reluctant to try to undo them for shearing the bolts because of corrosion and the bolt heads in poor condition. My local garage also said they were concerned about the bolts shearing because if the bolts did it would be an expensive fix. The current alignment is not very far out and the advice I've been given is to leave it alone as I don't do much mileage and the general age of the car, it's done 170k. Any advice welcome, I'm tempted to buy some decent sockets and try with a breaker bar but also vary wary at the same time. Tia, Martyn |
28th May 2021, 16:33 | #2 |
Premium Trader
Rover 75 Join Date: Nov 2010
Location: Devon
Posts: 33,764
Thanks: 8,837
Thanked 14,831 Times in 8,030 Posts
|
Never had one shear off yet! Also I’ve had to remove a cross threaded one put in by a ham fisted garage, retap the thread and fit a new bolt.
I find garages reluctant to do these as well, I always crack them off before going to have tracking done.
__________________
Lest we forget..
|
28th May 2021, 17:03 | #3 | |
Posted a thing or two
MGB GT, 2 Morris Minor Travellers Join Date: May 2011
Location: Bilston
Posts: 1,661
Thanks: 1,610
Thanked 497 Times in 370 Posts
|
Quote:
Martyn Last edited by squire; 28th May 2021 at 17:07.. Reason: Typo |
|
28th May 2021, 17:23 | #4 |
Premium Trader
Rover 75 Join Date: Nov 2010
Location: Devon
Posts: 33,764
Thanks: 8,837
Thanked 14,831 Times in 8,030 Posts
|
You can get to these with the car on its wheels! A long socket and a stubby extension is what I use.
Sent from my iPhone using Tapatalk
__________________
Lest we forget..
|
28th May 2021, 19:38 | #5 | |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Quote:
|
|
28th May 2021, 19:59 | #6 |
Posted a thing or two
MGB GT, 2 Morris Minor Travellers Join Date: May 2011
Location: Bilston
Posts: 1,661
Thanks: 1,610
Thanked 497 Times in 370 Posts
|
Yes, it's been over 4 years since it was last done and there was feathering on the outside edges, I was advised to get it checked when it was MOTed.
|
28th May 2021, 21:06 | #7 |
Loves to post
Rover75 tourer Join Date: Jun 2018
Location: Ashton
Posts: 428
Thanks: 121
Thanked 206 Times in 145 Posts
|
Sometimes with bolts such as these and the position they are in, especially when working on ramps or axle stands on your back, is to apply enough pressure between socket and bolt head to prevent it ' camming out '.
One way to help to prevent this is to use a breaker bar and apply pressure to the socket end of the bar with a jack to push and hold the socket firmly on to the bolt head, it's only needed to crack the bolt loose. One slight disadvantage is that there is a loss of feel.
__________________
Common sense isn't a gift, it's a punishment because you have to deal with everyone who doesn't have it. |
28th May 2021, 21:12 | #8 |
Loves to post
Rover 75 Saloon Join Date: Sep 2020
Location: Edinburgh
Posts: 291
Thanks: 133
Thanked 102 Times in 61 Posts
|
I stood and watched while a guy tried with all his might to get the bolts on one side to move. He got one going but the others he looked like his arm was going to snap trying. His socket kept slipping off too leading to him bashing his knuckles. They had no heat at the time. Felt bad for the guy and I thought the bolt heads would be getting mashed so we called it a day.
He ended up saying if I could get new bolts in and bring it back they would do my tracking. No charge to be fair. May I ask where you sourced the replacement bolts? I got a wee bit lost back when I was researching it and eventually forgot about it! |
28th May 2021, 21:29 | #9 | |
Posted a thing or two
MGB GT, 2 Morris Minor Travellers Join Date: May 2011
Location: Bilston
Posts: 1,661
Thanks: 1,610
Thanked 497 Times in 370 Posts
|
Quote:
|
|
28th May 2021, 21:39 | #10 | |
Loves to post
Rover75 tourer Join Date: Jun 2018
Location: Ashton
Posts: 428
Thanks: 121
Thanked 206 Times in 145 Posts
|
Quote:
Yes a bit of heat works wonders. I have an old BOC O series welding torch which is great for such situations, with a no.1 tip and using oxy acetylene or oxy propane with a no. 1 propane tip I have a small flame with a small plume and if used with care can get into some odd spots without damaging or heating other components. However my fall back for heating stubborn nuts, bolts and so on where a flame will cause damage is to use my sons induction kit, not cheap but seeing a bolt, or nut glow at up to 800c in a few seconds and unscrew like a new one is amazing.
__________________
Common sense isn't a gift, it's a punishment because you have to deal with everyone who doesn't have it. |
|
|
|