|
||
|
28th March 2022, 08:01 | #1 |
This is my second home
All Trophy Blue ,ZT260#50 , ZT CDTI Auto, ZR105+ and 1.8T Firefrost spoiling the Set . Join Date: Nov 2006
Location: Nr Sherborne But in Somerset..
Posts: 6,078
Thanks: 916
Thanked 1,214 Times in 768 Posts
|
general Brake question
why do some brakes/pads decide only to use a patch/strip around a disc and not the whole area ??
one of my rears only uses a 1 inch wide area right in the middle C
__________________
The Three Bloo's Wifey's Zr105, MY CDTI & 260 #50 and Number One sons 1.8T in Firefrost When I were a lad Zero to 142 in 10.25 secs at the Pod on my Blown Norton. 210 Kart Champ in 70's |
28th March 2022, 08:18 | #2 |
This is my second home
Rover 75 Saloon & Tourer Join Date: Sep 2012
Location: Lincoln
Posts: 14,935
Thanks: 1,630
Thanked 3,032 Times in 2,181 Posts
|
either the pad or disc is "bowed" or has a high/low spot?
I am surprised that wheel passes the mot as I would expect the brake performance to be poor on that wheel macafee2 |
28th March 2022, 09:43 | #3 | |
Regular poster
MG ZT 260 #442 in XPower Grey Join Date: Mar 2022
Location: Warwick
Posts: 61
Thanks: 4
Thanked 14 Times in 12 Posts
|
Quote:
Suggests that perhaps there's a problem with the top and bottom arcs of the current pads not touching the disc, or there was a problem with the centre arc of the previous pads (so the top and bottom did wear the disc down leaving the centre arc proud). Without machining the disc and the pads to get them all level, changing both seems the obvious answer.
__________________
MG ZT 260 #442 in XPower Grey and Cupra Formentor Hybrid VZ2 |
|
28th March 2022, 11:51 | #4 | |
This is my second home
75 Contemporary SE Mk II 2004 Man. Sal. CDTi 135ps, FBH on red diesel, WinCE6 DD Join Date: May 2010
Location: Leeds
Posts: 17,273
Thanks: 2,160
Thanked 2,061 Times in 1,586 Posts
|
Quote:
Mine have always been like that, never a problem with passing MOT's it is normal for the 75 rear brake discs.
__________________
Harry How To's and items I offer for free, or just to cover the cost of my expenses... http://www.the75andztclub.co.uk/foru...40#post1764540 Fix a poor handbrake; DIY ABS diagnostic unit; Loan of the spanner needed to change the CDT belts; free OBD diagnostics +MAF; Correct Bosch MAF cheap; DVB-T install in an ex-hi-line system; DD install with a HK amp; FBH servicing. I've taken a vow of poverty. To annoy me, send money. |
|
28th March 2022, 12:05 | #5 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,412
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Quote:
Whilst you're at it, check that the piston moves freely when the brake pedal is depressed in a controlled manner. Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
|
28th March 2022, 21:20 | #6 | |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Quote:
Also the pads will wear faster due to the excessive pressure. Altogether not a good thing. ( Can even lead to brake failure due to over heating when descending a long steep hill for instance. )---- |
|
28th March 2022, 22:34 | #7 |
Posted a thing or two
rover 75 club se Join Date: Apr 2011
Location: Leicester
Posts: 1,673
Thanks: 358
Thanked 419 Times in 310 Posts
|
if you look at alot of these pads , and pay careful attention to the spring clips that hold them inside the piston, more often than not , they are either not positioned centrally or equal. i have noticed this times on different makes. i had one set that would go in reluctantly , and pop back out at the slightest tap on the calliper. sometimes the springs were twisted at an angle or not even the same sizes . i wonder if the clips push out the pads at an angle whilst driving and then re seat when the pedal is applied. some of the new ones are a pain to fit inside the piston and must distort once inside , to an aukward angle and then not give a square initial contact at all. you can try to adjust them equally with the help of some moles but never get them equal as the spring material is very tough. the rear brakes never get much pressure on them as most of the braking is done on the fronts. sometimes the central rivets are not even central to the pad, and vary even on expensive pads. this would also give you problems on the pad carriers with the pads sticking. things aint what they use to be is an understatement...
|
29th March 2022, 13:24 | #8 | |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Quote:
|
|
29th March 2022, 14:00 | #9 |
Posted a thing or two
rover 75 club se Join Date: Apr 2011
Location: Leicester
Posts: 1,673
Thanks: 358
Thanked 419 Times in 310 Posts
|
please read my post again mr colvert. .... the o.p was asking about uneven pad wear. i was suggesting in my post that the pads whilst the vehicle was moving were actually springing out at an angle and could possibly be in contact with the discs at an angle thus wearing unevenly. this would also cause the pads to not sit squarely on the metal carrier guides. the pads wont move out of centre once they are up to the piston whilst being applied , thats true, but do we know that they are , and that they are fully square to the piston ? it would only take a very small amount out of square to effect them. ...
|
29th March 2022, 14:07 | #10 |
Posted a thing or two
rover 75 club se Join Date: Apr 2011
Location: Leicester
Posts: 1,673
Thanks: 358
Thanked 419 Times in 310 Posts
|
the springs are quite capable of pushing back a piston. provided of course it moves freely and is not sticking or seized. sometimes , as i have said in a previous post they can take quite a bit of forcing into the piston, no matter how square you try to offer them in....
|
|
|