Abs sensor feed

The Incredible 'ULK' · 17th April 2015, 21:01

Hi everyone, I've finally managed to get round to fitting my highline today, I still have a couple of things to do, one of them is the ABS sensor connection, after routing around I can't seem to find it. Where abouts should I be looking? Any help greatly appreciated

Greeners · 17th April 2015, 21:04

lives behind the ash tray, some early cars weren't fitted with the connector

The Incredible 'ULK' · 17th April 2015, 21:09

Quote:

Originally Posted by Greeners

lives behind the ash tray, some early cars weren't fitted with the connector

Thanks Greeners
Would an early Longbridge car (2001), be early enough not to have it?

Greeners · 17th April 2015, 21:15

I'd expect it to, there's a thread somewhere detailing it, try the highline section towards the back / oldest posts

The Incredible 'ULK' · 17th April 2015, 21:34

Ok, will have a look

Thanks for the advice

maxi_crawf · 18th April 2015, 08:00

Hiding behind the dash, coming off the main loom there is about 8" of loose wire with the flat black plug on the end, I found the other end on the passenger side low down behind the "kick panel"
sleeve up, arm in and a good root around (bit like a gynaecologist really

)

Hope it's all going well with the Chariot

Greeners · 18th April 2015, 12:39

Quote:

Originally Posted by Greeners

I'd expect it to, there's a thread somewhere detailing it, try the highline section towards the back / oldest posts

here you go

The Incredible 'ULK' · 18th April 2015, 18:00

Thanks chaps, I'll have a look again tomorrow.

Quote:

Originally Posted by maxi_crawf

Hiding behind the dash, coming off the main loom there is about 8" of loose wire with the flat black plug on the end, I found the other end on the passenger side low down behind the "kick panel"
sleeve up, arm in and a good root around (bit like a gynaecologist really

)

Hope it's all going well with the Chariot

Thanks mate, its coming together slowly, looks a lot better from when you last saw it.

The Incredible 'ULK' · 19th April 2015, 09:34

Well after a good root I still haven't found it, I've had my head right under looking up to where it joins the main harness above the airbag, and theres nothing strapped up, so I think its fair to say I don't have it. So I need to fit a feed in somewhere, anywhere else I can get the signal from inside the car?

Greeners · 19th April 2015, 14:58

Quote:

Originally Posted by The Incredible 'ULK'

Well after a good root I still haven't found it, I've had my head right under looking up to where it joins the main harness above the airbag, and theres nothing strapped up, so I think its fair to say I don't have it. So I need to fit a feed in somewhere, anywhere else I can get the signal from inside the car?

I think you'll have to pick it up from the ABS ECU under the bonnet.

need to find the thread of the owner that had a similar problem

17th April 2015, 21:01	#1
The Incredible 'ULK' Loves to post Rover 75 Saloon Join Date: Aug 2014 Location: Withernsea Posts: 399 Thanks: 131 Thanked 127 Times in 78 Posts	Abs sensor feed Hi everyone, I've finally managed to get round to fitting my highline today, I still have a couple of things to do, one of them is the ABS sensor connection, after routing around I can't seem to find it. Where abouts should I be looking? Any help greatly appreciated

17th April 2015, 21:04	#2
Greeners Moderator MG-ZTT Join Date: Mar 2007 Location: Ware, Herts Posts: 19,798 Thanks: 161 Thanked 1,249 Times in 1,036 Posts	lives behind the ash tray, some early cars weren't fitted with the connector __________________ *David* Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics]

17th April 2015, 21:15	#4
Greeners Moderator MG-ZTT Join Date: Mar 2007 Location: Ware, Herts Posts: 19,798 Thanks: 161 Thanked 1,249 Times in 1,036 Posts	I'd expect it to, there's a thread somewhere detailing it, try the highline section towards the back / oldest posts __________________ *David* Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics]

17th April 2015, 21:34	#5
The Incredible 'ULK' Loves to post Rover 75 Saloon Join Date: Aug 2014 Location: Withernsea Posts: 399 Thanks: 131 Thanked 127 Times in 78 Posts	Ok, will have a look Thanks for the advice

18th April 2015, 08:00	#6
maxi_crawf Posted a thing or two R75 Saloon Conn CDT SE, MG ZT190+ Join Date: Nov 2006 Location: Kingston-upon-Hull Posts: 1,960 Thanks: 823 Thanked 426 Times in 274 Posts	Hiding behind the dash, coming off the main loom there is about 8" of loose wire with the flat black plug on the end, I found the other end on the passenger side low down behind the "kick panel" sleeve up, arm in and a good root around (bit like a gynaecologist really ) Hope it's all going well with the Chariot

19th April 2015, 09:34	#9
The Incredible 'ULK' Loves to post Rover 75 Saloon Join Date: Aug 2014 Location: Withernsea Posts: 399 Thanks: 131 Thanked 127 Times in 78 Posts	Well after a good root I still haven't found it, I've had my head right under looking up to where it joins the main harness above the airbag, and theres nothing strapped up, so I think its fair to say I don't have it. So I need to fit a feed in somewhere, anywhere else I can get the signal from inside the car?