|
||
|
9th January 2020, 16:58 | #1 |
Avid contributor
MG ZT Join Date: Jan 2016
Location: Stoke-on-Trent
Posts: 197
Thanks: 278
Thanked 36 Times in 23 Posts
|
Heater problem gremlin
Hi All, had a problem with my heater, it worked perfectly, for about 15 miles, then suddenly it went cold, tried it the next day,on a short trip, and it went back to the normal temperature,has anyone had a similar problem, if so, is it anything to get concerned over, or is it just a dreaded gremlin attack
|
9th January 2020, 17:13 | #2 |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Not usual with the diesel engine as air locks seem to be rare.
Is the water level in the header tank correct ? |
9th January 2020, 18:28 | #3 |
Avid contributor
MG ZT Join Date: Jan 2016
Location: Stoke-on-Trent
Posts: 197
Thanks: 278
Thanked 36 Times in 23 Posts
|
thanks for the reply,i will check the level tomorrow, and will let you know,if it needs a top up.
|
9th January 2020, 18:32 | #4 |
Posted a thing or two
V6 2ltr auto in copperleaf +CDTI Auto in Royal Blue on loan to Son Join Date: Jul 2010
Location: Tewkesbury, Gloucestershire
Posts: 1,709
Thanks: 105
Thanked 476 Times in 267 Posts
|
Did you have the air con running? If so, that's what happens when the set temperature is reached.
__________________
|
9th January 2020, 21:35 | #5 |
Avid contributor
MG ZT Join Date: Jan 2016
Location: Stoke-on-Trent
Posts: 197
Thanks: 278
Thanked 36 Times in 23 Posts
|
no mate, didn't have the air- con on, but thanks for the suggestion,
|
9th January 2020, 21:49 | #6 |
Premium Trader
Rover 75 Join Date: Nov 2010
Location: Devon
Posts: 33,770
Thanks: 8,837
Thanked 14,831 Times in 8,030 Posts
|
We had an airlock in Debs diesel, the heater never got hot from the day we got the car, ended up backflushing the heater matrix then refilling the whole system, it now has a heater that's on par with a petrol model.
__________________
Lest we forget..
|
10th January 2020, 17:30 | #7 |
This is my second home
Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4. Join Date: Jul 2009
Location: Hampshire
Posts: 11,549
Thanks: 3,470
Thanked 3,119 Times in 2,247 Posts
|
|
10th January 2020, 18:34 | #8 |
Avid contributor
ZT-T Join Date: Sep 2019
Location: Teesside
Posts: 235
Thanks: 176
Thanked 66 Times in 38 Posts
|
Just to back up previous comment, I had an airlock on my CDTi after water pump replacement and I experienced the cold heater.
Followed advice on this forum and all fine. I didn't empty and flush and refill slowly but did use the bleed screw on the hose near the battery box. JohnnyBG |
10th January 2020, 18:48 | #9 | |
This is my second home
MG ZT CDTi Join Date: Jan 2014
Location: carrick
Posts: 7,859
Thanks: 3,494
Thanked 2,657 Times in 1,973 Posts
|
Quote:
When you say it went cold, did all the vents go cold? When set to auto, and it has reached its target temp, the upper vents on the driver's side will cool down. I always thought this was meant to be a few degrees lower, but mine feels much cooler than this, to the point it feels cold. The feet level vents will remain warm as well as all the passenger side vents. Once in this status it will be as follows; Driver's side window vent = cool Driver's side door vent = cool Driver's side face vents (if used) = cool Driver's side foot vents = warm Driver's side rear foot vent = warm Passenger's side window vent = warm Passenger's side door vent = warm Passenger's side face vents (if used) = warm Passenger's side foot vents = warm Passenger's side rear foot vent = warm There is a way to over ride it, but I cannot remember, I think it was either switching off the auto mode, or putting it on to recirc. Increasing the temp will override it, but only until that target temp has been reached. In my car, the target temp would be reached after approximately 15 miles (I drive with the window down a little). So if your next 'short' run as you described, was short enough that the target temperature within the car was not yet reached, then you wouldnt notice it. I would actually reckon most people do not notice it under normal use. -------------------------------------- if all the vents are cold, then it is likely to be an airlock or blockage somewhere, and just ignore the above lol.
__________________
It is not gloss primer .............. it is duct tape silver! |
|
10th January 2020, 20:46 | #10 | |
This is my second home
Rover75 and Mreg Corsa. Join Date: Nov 2006
Location: Sumweer onat mote o'dust (Sagin)
Posts: 21,753
Thanks: 341
Thanked 3,660 Times in 2,924 Posts
|
Quote:
1. Remove the bleed screw from fuel burning heater coolant return hose. 2. Have available the prepared coolant. 3. Fill the cooling system, keeping coolant level to neck of expansion tank, until a steady stream of coolant is emitted from bleed screw hole. Fit and tighten bleed screw. 4. Continue filling until coolant reaches expansion tank neck and remains static. 5. Ensure A/C is switched off. 6. With the expansion tank cap off. start and run engine and run at 2000 - 3000 rev/min. Fill expansion tank as necessary to maintain coolant level just below expansion tank neck. When coolant starts to rise up expansion tank neck, due to heat expansion, fit expansion tank cap. 7. Continue running engine at 2000 - 3000 rev/ min until cooling fan comes on and then run at idle speed until cooling fan stops. 8. Switch off engine and allow it to cool for 30 minutes. 9. Check cooling system for leaks. 10. Remove expansion tank cap and if necessary top-up coolant to MAX level. If MAX mark is not visible, remove excess coolant until level is at MAX mark. Warning - To avoid scalding injury, do not remove the filler cap from the expansion tank while the system Is hot 11. Refit expansion tank cap. A top up and bleed isn't exactly the same as refilling an empty system since the latter forces all air in the circuit upwards so it exits at the screw hole. It will therefore be worth removing the bleed screw after this routine to ensure no circulating air has collected in the area of the bleed screw. TC Last edited by T-Cut; 10th January 2020 at 20:53.. |
|
|
|