|
||
|
|
5th February 2019, 14:09 | #1 |
Regular poster
rover 75 connie diesel estate se Join Date: Nov 2013
Location: teignmouth devon
Posts: 41
Thanks: 8
Thanked 1 Time in 1 Post
|
car wont start
75 con not been used for some time,went out yesterday,20 miles did some shopping,started fine,20 miles back,stopped at another shop,came out would not start,turns over fine,had breakdown out said it could be elec fuel punp,fitted new one today,still the same,how long does it take to self prime,new fuel and oil fitted and all belts and oil change in last few months,recovery man was talking about crank shaft fuel sender,????anyone got any ideas please
|
5th February 2019, 15:30 | #2 |
I really should get out more.......
Rover 75 Saloon Join Date: Jul 2011
Location: Gävle
Posts: 2,538
Thanks: 395
Thanked 823 Times in 652 Posts
|
You’ve got a T4 equipped garage in Newton Abbot (Exeter Road Garage) just down the road from you. They should be able to pinpoint the problem with the T4, and save you a lot of time / expense guessing and replacing parts needlessly.
Regards |
5th February 2019, 16:42 | #3 |
MG ZT Join Date: Jan 2011
Location: Newcastle Upon Tyne
Posts: 20,151
Thanks: 3,565
Thanked 10,837 Times in 5,718 Posts
|
Harry, make sure the ECM isn't sitting in a puddle, and see if there is 12v present on the white/purple wire of the fuel pump.
Brian |
5th February 2019, 17:03 | #4 |
Gets stuck in
rover 75 saloon cdt club se re map 160 bhp Join Date: Dec 2018
Location: sheffield
Posts: 558
Thanks: 227
Thanked 169 Times in 135 Posts
|
can you hear your ubp kicking in when your key is at postion 2 or as Brian says check your plenums make sure your ecu not taken a bath i had the same problem a month ago rgds mark
|
5th February 2019, 17:48 | #5 |
Regular poster
rover 75 connie diesel estate se Join Date: Nov 2013
Location: teignmouth devon
Posts: 41
Thanks: 8
Thanked 1 Time in 1 Post
|
wont start
have got fuel up to the filter and my oil light is on, no water by ecu done most weeks,tomorrow I will crack the injectors to make surh fuel is getting to engine,will test wire as suggested,many thanks to all will keep updating regards harry
|
5th February 2019, 17:54 | #6 |
MG ZT Join Date: Jan 2011
Location: Newcastle Upon Tyne
Posts: 20,151
Thanks: 3,565
Thanked 10,837 Times in 5,718 Posts
|
Don't crack the injector unions Harry, the rail pressure on crank alone is 2200 psi, will the car start with a sniff of easistart?
|
6th February 2019, 15:29 | #7 |
Regular poster
rover 75 connie diesel estate se Join Date: Nov 2013
Location: teignmouth devon
Posts: 41
Thanks: 8
Thanked 1 Time in 1 Post
|
wont start
it is not the cam sensor ,just tested it in range rover and its ok regards harry
|
6th February 2019, 20:50 | #8 |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Harry. Please read the other posts.---
|
8th February 2019, 09:26 | #9 |
Regular poster
rover 75 connie diesel estate se Join Date: Nov 2013
Location: teignmouth devon
Posts: 41
Thanks: 8
Thanked 1 Time in 1 Post
|
wont start
just sent my ecu up to the wizard of the north marinabrian to see what magic he can work,hope it is that otherwise I wont have a clue what is wrong will have to relies on you good members to help me out as I am not mechanically minded,thanks to all regards harry
|
9th February 2019, 10:21 | #10 | |
MG ZT Join Date: Jan 2011
Location: Newcastle Upon Tyne
Posts: 20,151
Thanks: 3,565
Thanked 10,837 Times in 5,718 Posts
|
Quote:
As suggested you could have a word with Lynne and Tim at Exeter Road garage next. You are only about five miles away from them, Find them HERE Remember to tell them I sent you Your ECM is back in the post, so you should have it on Monday. Brian |
|
|
|