|
||
|
1st June 2009, 08:45 | #1 |
NI/ROI RS
ZT-T 190 / 75 Diesel x3 / 6 door limo / 216 Cabby / Rover 25 van Join Date: May 2009
Location: Antrim
Posts: 8,103
Thanks: 299
Thanked 1,046 Times in 568 Posts
|
Fao all Zt and Zt-t owners, both mk1 and mk2 - who can help?
Lookin all zt/zt-t (mk1 and 2) owners for a tiny easy help.
I need a few people to measure their grille Mg badge size and the boot Mg badge size. Get the tape measure out! IF they are standard accross the range, have a we look and see if your various cars match the measurements below. Thanks. Mk1 zt Front grill mg badge - 59mm Rear mg badge - 40mm Doing a bit of research and may be able solve the fading badge problem for everyone. |
1st June 2009, 09:57 | #2 |
Loves to post
MG ZT 190+ Join Date: Nov 2006
Location: Newcastle under Lyme
Posts: 305
Thanks: 0
Thanked 0 Times in 0 Posts
|
The above measurements are correct for the Series 1
|
1st June 2009, 10:28 | #3 |
Avid contributor
MG-ZT-T cdti Join Date: Jul 2008
Location: Big Hill
Posts: 219
Thanks: 8
Thanked 2 Times in 2 Posts
|
My 06 reg ztt is front-59mm back -45mm
|
1st June 2009, 10:39 | #4 |
Banned
180+ Sport Auto Join Date: Oct 2006
Location: Bedford Middle Level
Posts: 17,787
Thanks: 0
Thanked 18 Times in 5 Posts
|
Make sure any of these badges get a good coat of a sealer before installing. I used clear nail varnish, which lasted over 4 years before the dreaded de-lamination started.
I am about to install a new one, this time I intend a few coats of clear lacquer as I have some available. I'll report back in 4 years or less. |
1st June 2009, 11:10 | #5 | |
This is my second home
15 years of 75s & ZTs now an XTrail Join Date: Nov 2006
Location: Danbury, Essex
Posts: 3,761
Thanks: 18
Thanked 88 Times in 56 Posts
|
Quote:
__________________
ZT 190 X Power Grey The Only Colour is this Dark Silver!! When I was a kid I was scared of earwigs because I thought they actually lived in your ears. I was even more terrified of cockroaches! |
|
1st June 2009, 17:09 | #6 |
Feel the size of my Quads
MG ZT 440SE, MG HS PHEV & MG3 Join Date: Nov 2006
Location: Addlestone
Posts: 1,735
Thanks: 0
Thanked 128 Times in 85 Posts
|
If you are going for a replacement should be 57mm and 40mm (ZT) 44mmZTT)
I've been involved with the ZT enamel badges so have some dealings with the sizes. The 40mm rear is very tight and if I was going to do it again would reduce to 39mm. Back of the om ones and the two-sixties relacement From Sharky's car, dark front highlights it better than my silver.
__________________
Member 23 or 63 depending on what you look at. https://www.two-sixties.co.uk/mgoc26...0rum/forum.php http://two-sixties-blog.com/ http://www.youtube.com/user/TheTwoSi.../1/1wPt2rhd_Ps |
|
|