|
||
|
28th February 2020, 17:11 | #1 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
Valve collets/keepers
I am in the process of overhauling the two cylinder heads on my Rover 75 connoisseur. All was well until it came to replacing the collets. I went to youtube after 2or 3 frustrating hours. Here is the solution and it really does work. I found that because the Rover's collets are so tiny they insisted on adhering to the plastic that the author of this video uses. I used a piece of duct tape folded over so that the adhesive side is on the inside. Even at that the collets tended to stick to the duct tape but the solution is to place a piece of polythene from a freezer bag between the duct tape and the valve spring retainer cap. It works because as you compress the spring the plastic stretches over the valve stem and as it does it presses the collets agains the valve stem. This really does work.
The link is: https://www.youtube.com/watch?v=xtO8ev0Q9jc Fred |
28th February 2020, 18:45 | #2 |
same car since 2005
2001 Rover 75 2.0 v6 Connoisseur Saloon Join Date: Nov 2006
Location: Ellesmere Port , Cheshire
Posts: 3,811
Thanks: 379
Thanked 549 Times in 466 Posts
|
I find that amazing if you hadn't done it yourself I would have said it wouldn't work on our heads ! I used a conventional spring compressor and wriggled the tiny collets in on the end of a magnetised screwdriver ; took ages and in fact drove me to drink …….. again
__________________
Who said it was simples ? |
1st March 2020, 10:02 | #3 |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Magnetise the collets.--They then stick to the valve stem.--
Done it lots of times and it works. |
1st March 2020, 11:38 | #4 |
same car since 2005
2001 Rover 75 2.0 v6 Connoisseur Saloon Join Date: Nov 2006
Location: Ellesmere Port , Cheshire
Posts: 3,811
Thanks: 379
Thanked 549 Times in 466 Posts
|
That's true , and they also stick with a dab of grease But these are the smallest collets I have come across and the trick was getting them into position in the first place , when using a conventional compressor
__________________
Who said it was simples ? |
5th March 2020, 22:42 | #5 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
I find that everything becomes magnetic. The forceps, screwdrivers and everything sticks to everything. Eventually lady luck intervenes and success! Then you start all over again with the next valve. The manufacturers must have had a clever trick that they are not telling us about. Seriusly though, the technique I have described does work. It seems to work best with inch suare pieces cut from the little pouches that some cat food comes in. Cats do have a use apart from catching mice.
Fred |
6th March 2020, 05:45 | #6 |
Posted a thing or two
Rover 75 2.0 V6 Auto Join Date: May 2011
Location: Sandnes - Norway
Posts: 1,560
Thanks: 64
Thanked 283 Times in 174 Posts
|
I have used a piece of tube as an extension on the valve-clamp. I have cut two "windows" in the tube to access the collets and put them in with a magnetised screwdriver and some grease on the valve stem. Time consuming work, but it works. I always put a rag over when releasing the clamp to avoid the collets fly away if not seated properly.
|
6th March 2020, 11:40 | #7 |
same car since 2005
2001 Rover 75 2.0 v6 Connoisseur Saloon Join Date: Nov 2006
Location: Ellesmere Port , Cheshire
Posts: 3,811
Thanks: 379
Thanked 549 Times in 466 Posts
|
Fred , do let us know how it all turns out in the end
You've had some fun with this one ……...
__________________
Who said it was simples ? |
7th March 2020, 15:44 | #8 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
I certainly will! The engine is now out. How do I post photographs? Do I have to use photobucket? I had great fun trying to extract the bigend bolts. The torx sockets i have jump from E14 to E16. Is there an E15? All the tool sets seem to omit E15. or are the big end bolts some b*****d- size?. I suppose I can't use the B*****d word.
Fred |
7th March 2020, 15:50 | #9 |
same car since 2005
2001 Rover 75 2.0 v6 Connoisseur Saloon Join Date: Nov 2006
Location: Ellesmere Port , Cheshire
Posts: 3,811
Thanks: 379
Thanked 549 Times in 466 Posts
|
In the "reply to thread" window , the toolbar at the top has a paperclip symbol . This will open another window which allows you to attach photos etc either from a website or from your hard drive . If your photos are too big they will need to be resized , but there is info provided there
__________________
Who said it was simples ? |
|
|