|
||
|
25th June 2015, 17:47 | #3571 |
Regular poster
Rover 75 Saloon Join Date: Feb 2015
Location: Wakefield
Posts: 99
Thanks: 71
Thanked 12 Times in 10 Posts
|
I have ordered a set of ford pins and cups.. will have to keep an eye on it and replace the whole plate later or weld a washer on the back to reinforce it then give a sand blast and fresh coat of paint.. After seeing how badly pitted rear disk are have ordered a set of them to.. so busy week next week before having to head off to Cornwall for a funeral..
|
25th June 2015, 17:51 | #3572 | |
This is my second home
MG ZT CDTi Join Date: Jan 2014
Location: carrick
Posts: 7,859
Thanks: 3,494
Thanked 2,657 Times in 1,973 Posts
|
Quote:
PIN 1 HOLD DOWN CUP PIN 2 Feed the pin from the back of the plate, it is fiddly, but still less fiddly than removing the back plate. My back plate was otherwise fine, and solid. That's why I didnt replace it.
__________________
It is not gloss primer .............. it is duct tape silver! |
|
25th June 2015, 22:19 | #3573 |
Gets stuck in
Mg zt ctdi Join Date: Jul 2010
Location: newcastle n.i
Posts: 537
Thanks: 76
Thanked 23 Times in 22 Posts
|
Stuck on some nice wind deflectors today
__________________
Mg zt 2004 cdti |
26th June 2015, 08:28 | #3574 |
Loves to post
MG ZT+ CDTi Join Date: Apr 2015
Location: N.Ireland
Posts: 475
Thanks: 81
Thanked 72 Times in 58 Posts
|
For past two days... nothing. Been out of action sick with the flu.
|
26th June 2015, 18:08 | #3575 |
Loves to post
75 oil burner ZX12R,ZRX1200R VN 1500,Uncle Bunt hardtail chop, Join Date: Mar 2015
Location: newcastle
Posts: 305
Thanks: 39
Thanked 152 Times in 67 Posts
|
found this in the "spare" headlamp i was about to polish & fit, as i'm a nice guy i wrapped the lens in a black boiler suit, left the open end pointing towards the workshop lights, by the time i had taken one rear bumper off the spares 75 & helped marinabrian remove & fit another one, it had done a flit
|
26th June 2015, 22:08 | #3576 |
This is my second home
none but not gone Join Date: Mar 2013
Location: March, Cambs
Posts: 16,437
Thanks: 894
Thanked 4,247 Times in 3,025 Posts
|
The Browns in this club feed on beer, curries and chocolate biscuits...
__________________
[SIGPIC][/SIGPIC]….All praise Bananaswan…. |
26th June 2015, 22:09 | #3577 |
Premium Trader
Rover 75 Join Date: Nov 2010
Location: Devon
Posts: 33,765
Thanks: 8,837
Thanked 14,831 Times in 8,030 Posts
|
They sure do buddy,they sure do
__________________
Lest we forget..
|
26th June 2015, 23:36 | #3578 |
Loves to post
mg zt cdti 160👍 Join Date: Jun 2014
Location: bath
Posts: 374
Thanks: 105
Thanked 50 Times in 43 Posts
|
fitted a new set of inlet gaskets to my vvc manifold , I think mickey mouse had fitted it originally as there was no gasket on the upper section of the inlet... this caused a vacuum leak and lumpy idle , all sorted now and with some nice fresh coolant to top it off
free photo hosting upload gambar Simples Last edited by bear-mg; 28th June 2015 at 14:53.. |
27th June 2015, 06:34 | #3579 |
Regular poster
Rover 75 Saloon Join Date: Jun 2014
Location: a/a
Posts: 70
Thanks: 18
Thanked 6 Times in 3 Posts
|
|
27th June 2015, 07:20 | #3580 |
Regular poster
Rover 75 Saloon Join Date: Jun 2014
Location: a/a
Posts: 70
Thanks: 18
Thanked 6 Times in 3 Posts
|
Did the Insurance claim - Rover is tough
Put in the insurance claim against the incompetent driver of a mondeo estate who managed to scrape my rear wheel arch. Estimated repair cost 600 quid!!!
Bet he will come of worse because his car was gouged along the complete side. Rover is tough. |
|
|