|
||
|
29th March 2024, 12:46 | #11 |
Posted a thing or two
rover 75 club se Join Date: Apr 2011
Location: Leicester
Posts: 1,683
Thanks: 358
Thanked 419 Times in 310 Posts
|
Another point is that if the shocks are not equal length when fully extended , then this will give a different ride height. I had this problem when i bought new shocks. The seller listed them as suitable for rover 75. They were in fact the mgzt rear shocks,which were shorter,as are the springs. Apparently , the last R75 used the mg set up on them, ( contempory models ) so ,if the shocks or springs are not the same each side , it will. Unless they were all renewed in pairs of the same,then you will have ride height differences. Even heavy duty springs (which i have fitted on the rear) sit much higher. When shorter shocks are fitted ,or shorter or stronger springs fitted, then they are already compressed lower than the originals. Simon has made a reply request,which i am interested in too ....
|
29th March 2024, 13:58 | #12 | |
Gets stuck in
MG ZT-T CDTi Join Date: Jul 2007
Location: Sunny Suffolk
Posts: 620
Thanks: 1
Thanked 16 Times in 13 Posts
|
Quote:
Explanation When a car is sitting in its normal position (rest), the suspension must be partly compressed. (Typically by 1/3 of its travel as I understand it.) This is so that the body can move both down and up relative to rest when it goes over bumps. A) If the damper were at its longest position when the car was at rest, when depressed it would go down, rebound to the rest position, then hit the top of the damper and break it. B) If the damper were at its shortest position when the car was at rest, when you pushed down it would not move as it would be acting as a solid rod, giving a very uncomfortable ride. An Aside Drag racing cars often have rigid or very stiff dampers so that they don't compress when starting off so that the weight on the wheels, and hence the grip, is better. I hope that helps. Last edited by Kearton; 30th March 2024 at 09:49.. |
|
29th March 2024, 14:26 | #13 |
Been absent for a while…
Rover 75 Tourer, Classic mini Cooper S, Abarth 595 competizione, MG TF and a Hyundai Tucson PHEV Join Date: Feb 2007
Location: Cumbria
Posts: 13,071
Thanks: 1,033
Thanked 1,686 Times in 1,040 Posts
|
It’s as simple as….
The springs are there to carry the weight of the vehicle and provide up and down movement of the suspension whilst keeping the vehicle level and to carry the weight of the vehicle. The ride height is regulated by the spring hence why you get ‘lowering’ springs. The damper is there to control and ‘dampen’ the operation of the Spring and in doing so keep the wheel on the road. The dampers are not weight carrying. You can get lowered or shorter dampers but these aren’t to do with the height of the vehicle but the height of the spring, a lowered spring needs a shorter damper to control it effectively.
__________________
................................................. 'Marmite' Possibly one of the most famous 75 tourers produced! left the production line as the last of only Three Rover 75 tourers produced in Trophy Yellow. 48 hours later Longbridge closed. The last sold ordered 75 Tourer. Paid for by the Phoenix Four and handed over by John Towers to the Warwickshire Northampton Air ambulance service as a Rapid Response vehicle |
29th March 2024, 17:50 | #14 |
Posted a thing or two
rover 75 club se Join Date: Apr 2011
Location: Leicester
Posts: 1,683
Thanks: 358
Thanked 419 Times in 310 Posts
|
Yes agreed. But everything mentioned in the past posts will depend upon having the correct shocks and springs fitted , and that they are all functioning equally and correctly. We wont know this until this status has been confirmed from the original poster. Variants in springs and shocks will bring different ride qualities and properties ,but most importantly is that they are equal each side .Thanks sworks for the post. ...
|
30th March 2024, 06:41 | #15 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,446
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Yes, thanks Mark and Kearton.
This is the interesting bit. I understand what you're saying Mark but if that was absolutely true wouldn't it be possible, with the car resting on its wheels, to undo the damper's fixings and just slide it out? But that's not possible. As Kearton has said, the damper is partially compressed. It contains gas under pressure so doesn't that provide some support to the body, albeit much less than the spring? Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
30th March 2024, 07:40 | #16 | |
Regional Secretary London South & West
75 Join Date: Mar 2012
Location: Reading
Posts: 1,045
Thanks: 395
Thanked 177 Times in 124 Posts
|
Quote:
View it another way . Springs hold the weight and absorb impacts. The 'shock absorbers' and in fact just dampers to dampen the springs rebound. All I / we can do is explain it to you , we can't make you understand it. Sent from my 2201116SG using Tapatalk
__________________
Andy T4.KV6 belt special tools [2002 MG ZT 2.5 177 manual Starlight silver 2004 MG ZT-T 1.8T 160 manual green |
|
30th March 2024, 07:45 | #17 | |
This is my second home
Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4. Join Date: Jul 2009
Location: Hampshire
Posts: 11,565
Thanks: 3,470
Thanked 3,119 Times in 2,247 Posts
|
Quote:
Simples! The only way shock absorbers can affect ride height (assuming the correct ones are fitted) is if they start to break up and debris blocks the internal channels the oil passes through. I've had this happen on my car where the NSR of the car got lower and lower as I drove because the shock absorber bound up until all the suspension movement was effectively used up. Left the car for half an hour and normal ride height was gradually resumed. . Last edited by Mike Noc; 30th March 2024 at 07:54.. |
|
30th March 2024, 07:53 | #18 | |
Posted a thing or two
Rover 75 Saloon Join Date: Mar 2014
Location: Louth
Posts: 1,430
Thanks: 380
Thanked 986 Times in 476 Posts
|
Quote:
|
|
30th March 2024, 09:42 | #19 | |
Gets stuck in
MG ZT-T CDTi Join Date: Jul 2007
Location: Sunny Suffolk
Posts: 620
Thanks: 1
Thanked 16 Times in 13 Posts
|
Quote:
At rest, the spring will be partly compressed and thus under load. The damper too will be partly compressed, but will not contain any pressure. A damper only contains pressure when it is moving. Its job is to slow down movement. It does this by restricting/slowing the flow of a fluid between its two chambers. Once that flow has been completed, there is no pressure. If the flow is blocked for any reason, the damper will behave like a solid rod. IHTH |
|
30th March 2024, 10:12 | #20 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,446
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Thank you Kearton. That's helpful.
Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
|
|