|
|
|
|
|
|
||
|
|
||
9th March 2018, 19:26
|
#1 |
|
Gets stuck in
MG ZT,MG ZT-T Join Date: May 2008
Location: St. Helens
Posts: 961
Thanks: 211
Thanked 235 Times in 158 Posts
|
Auto not starting in P
Hi All,
I have just started having trouble starting my auto in P. If I give it a knock forward it starts fine (just a bit worried if it gets worse)! I seem to recall a thread about a fix but can`t find anything in the searches can any kind soul point me to the thread please? Neil |
|
|
|
9th March 2018, 19:43
|
#2 |
|
SERVICING AND DEALER DIAGNOSTICS
MG ZT CDTI 135 + & MGZT CDTI AUTO 160 & ROVER 75 TOURER CDTI 160 TROPHY YELLOW Join Date: Aug 2013
Location: Hernebay
Posts: 4,331
Thanks: 818
Thanked 2,414 Times in 1,141 Posts
|
It’s probably the nut at the end of the linkage that needs adjusting, happens quite often. Hope that helps
Mick
__________________
[SIGPIC][/SIGPIC] T4 Owner Jobs done : new UBP, Spy hole mod, Rear hub(wheel bearing),plenum cleaned and emptied, Inline thermostat fitted,Full service, In car Digital tv/DVD Bluetooth Satnav etc, Replaced UBP, Restored headlights,Fixed airbag connection.replaced HP pump,replaced rear light seals,changed intercooler O rings. Jobs to do: ,replace drivers lock,.  [/SIZE]
|
|
|
|
|
9th March 2018, 19:43
|
#3 | |
|
This is my second home
none but not gone Join Date: Mar 2013
Location: March, Cambs
Posts: 16,437
Thanks: 894
Thanked 4,247 Times in 3,025 Posts
|
Quote:
Not expensive for another but a pain to get to....
__________________
 [SIGPIC][/SIGPIC]….All praise Bananaswan….
|
|
|
|
|
|
9th March 2018, 19:44
|
#4 |
|
Avid contributor
Rover 75 tourers(4)400turs(3 Join Date: Nov 2016
Location: Largs
Posts: 215
Thanks: 3
Thanked 67 Times in 56 Posts
|
Diesel Dick
Check the bush where the selector cable joins to the g/box it's a sort of nylon or hard rubber one through which passes the pin holding the cable it may be worn. Alternate solution start it with the selector in neutral.
|
|
|
|
|
9th March 2018, 19:45
|
#5 |
|
Gets stuck in
MG ZT,MG ZT-T Join Date: May 2008
Location: St. Helens
Posts: 961
Thanks: 211
Thanked 235 Times in 158 Posts
|
Thanks Mickyboywill check that out on my next day off! is it easy enough to get to?
Neil |
|
|
|
|
10th March 2018, 10:59
|
#6 | |
|
SERVICING AND DEALER DIAGNOSTICS
MG ZT CDTI 135 + & MGZT CDTI AUTO 160 & ROVER 75 TOURER CDTI 160 TROPHY YELLOW Join Date: Aug 2013
Location: Hernebay
Posts: 4,331
Thanks: 818
Thanked 2,414 Times in 1,141 Posts
|
Quote:
Yeah its really easy to do mate just look under the car at the gearbox where the arm meets the cable, might need a very very slight adjustment, had to adjust quite a few before on different 75’s. Less than a 5 min job, if you was near mine I’d have done it outside the house lol Mick
__________________
[SIGPIC][/SIGPIC] T4 Owner Jobs done : new UBP, Spy hole mod, Rear hub(wheel bearing),plenum cleaned and emptied, Inline thermostat fitted,Full service, In car Digital tv/DVD Bluetooth Satnav etc, Replaced UBP, Restored headlights,Fixed airbag connection.replaced HP pump,replaced rear light seals,changed intercooler O rings. Jobs to do: ,replace drivers lock,. [/SIZE]
|
|
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
