|
||
|
|
29th September 2017, 13:42 | #1 |
Gets stuck in
Rover 75 Tourer Join Date: Mar 2013
Location: Gainsborough
Posts: 580
Thanks: 31
Thanked 45 Times in 39 Posts
|
Sill repair panels
Are repair sections available for the sills or is it a fabrication job?
|
29th September 2017, 17:26 | #2 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,370
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
It's a fabrication job Alex, unless you want to buy a third of the side of the car!
I've just had my NSR repaired which included making a new support bracket. It's an expensive job, but as it's just about the only bodywork weakness on the car it's worth it in my view. Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
29th September 2017, 21:07 | #3 |
Premium Trader
Rover 75 Join Date: Nov 2010
Location: Devon
Posts: 33,766
Thanks: 8,837
Thanked 14,831 Times in 8,030 Posts
|
The easiest way is to cut a good piece of sill from a donor car.
__________________
Lest we forget..
|
29th September 2017, 22:38 | #4 |
Gets stuck in
Rover 75 Tourer Join Date: Mar 2013
Location: Gainsborough
Posts: 580
Thanks: 31
Thanked 45 Times in 39 Posts
|
Haha wonder of anyone has a good one they will let me chop out
Most of the rust is out now, front jacking points seem ok so just the back ones, and inner and outer sills to do ... going to be a long weekend then ! A uprising what the underseal hid, looked perect other than a tiny rust stain and now I'm missing abut a foot of sill either side |
30th September 2017, 09:19 | #5 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,370
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Alex; here is what remained of my NS lift support bracket:
So I'm not sure that you could rely upon a donor car to offer anything useful. And the reconstruction from sheet metal: Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
30th September 2017, 11:23 | #6 |
MG ZT Join Date: Jan 2011
Location: Newcastle Upon Tyne
Posts: 20,151
Thanks: 3,565
Thanked 10,837 Times in 5,718 Posts
|
The chickens have come home to roost on that job
I certainly wouldn't rely on that to jack up the car, and the rust is peeking through the primer on the inner sill Brian |
1st October 2017, 11:51 | #8 |
Premium Trader
Rover 75 Join Date: Nov 2010
Location: Devon
Posts: 33,766
Thanks: 8,837
Thanked 14,831 Times in 8,030 Posts
|
There are still plenty of good sills left on scrap cars, it's hit and miss though as you can't say later cars will be ok and early Ines rusty, I have seen good and bad in both mk1 & mk2
__________________
Lest we forget..
|
14th June 2018, 02:12 | #9 |
Newbie
rover75 2.5 v6 connisour SE 2003 Join Date: Apr 2009
Location: birmingham
Posts: 11
Thanks: 2
Thanked 0 Times in 0 Posts
|
rear jacking points and sill rotten help needed
Hi all just a quick question on this subject. On cutting through the sill and removing the rotten out sill section is the sill spot welded on the underside or bonded I'm only asking as I now have the dreaded rotten sill / jacking points on the rear I've sourced a complete new outer sill repair panel from eBay £49 I just wondered how the sill is fixed at the bottom
|
14th June 2018, 06:18 | #10 |
This is my second home
Rover 75 Tourer/ MG ZT-T 400 Join Date: May 2012
Location: Lhanbryde
Posts: 3,278
Thanks: 2,627
Thanked 1,523 Times in 869 Posts
|
I can only concur with Marinabrian’s comments in post 11, I’d not be happy with that repair on my car. I’m confused as the OP states in post 5 “NS lift support bracket” then in post 7 “it’s not an official jacking point”. So which is it ? I’m in agreement with Marinabrian in post 8 that the jacking pad does indeed fit into that section
|
|
|