|
||
|
2nd February 2021, 23:28 | #11 |
Avid contributor
Rover 75 Saloon CDTi, MG ZT CDTi Join Date: Apr 2016
Location: Portarlington
Posts: 135
Thanks: 66
Thanked 25 Times in 19 Posts
|
Ok Guys....I am sorry to say the issue is with my laptop......It will not install the correct driver. I have installed Toaf on my work laptop and it is working fine.
Now to the reason I needed this.... I set the lights to be DRL. and after disabling this, I now have no side \park lights. I have a nback of the LCM form last april before I did this, but when I select the file to restore it does not seem to restore the file. I have tested a back I took today and this seems to restore. Any Ideas, could it be the version of Toaf that I used in April 5.00.43 as I have the latest version now of 5.00.51 now installed. If I dont get this to work I might just for the NCT run a cable from the rear light to power the park\side lights in the front. Is side lights an NCT failure does anyone now?
__________________
Working on: Rover 75 CDTi Copperleaf Today is just yesterdays tomorrow..... |
3rd February 2021, 04:58 | #12 |
I really should get out more.......
Rover 75 Saloon Join Date: Jul 2011
Location: Gävle
Posts: 2,534
Thanks: 395
Thanked 823 Times in 652 Posts
|
You could always try the earlier version, or install the LSM from the website which you'd need to configure, but just checked and the Toaf website is down again.
I don't have the LSM file but perhaps someone else does, Hogweed? Regards ps. And now the website is back up again ! Last edited by vitesse; 3rd February 2021 at 05:00.. |
3rd February 2021, 05:45 | #13 |
Avid contributor
Rover, few of them Join Date: Aug 2011
Location: Split, Croatia
Posts: 235
Thanks: 254
Thanked 117 Times in 82 Posts
|
If you still need LCM file, I have it. But since Toaf site is working, you can download it? There are two versions: standard and xenon one.
|
3rd February 2021, 16:03 | #14 |
Avid contributor
Rover 75 Saloon CDTi, MG ZT CDTi Join Date: Apr 2016
Location: Portarlington
Posts: 135
Thanks: 66
Thanked 25 Times in 19 Posts
|
OK so I have the file how do I config it to match my car???
__________________
Working on: Rover 75 CDTi Copperleaf Today is just yesterdays tomorrow..... |
3rd February 2021, 16:47 | #15 |
same car since 2005
2001 Rover 75 2.0 v6 Connoisseur Saloon Join Date: Nov 2006
Location: Ellesmere Port , Cheshire
Posts: 3,811
Thanks: 379
Thanked 549 Times in 466 Posts
|
I recall reading somewhere that the 43 version of TOAF allowed more things than the later 51 version
__________________
Who said it was simples ? |
3rd February 2021, 17:20 | #16 |
I really should get out more.......
Rover 75 Saloon Join Date: Jul 2011
Location: Gävle
Posts: 2,534
Thanks: 395
Thanked 823 Times in 652 Posts
|
|
3rd February 2021, 17:21 | #17 |
I really should get out more.......
Rover 75 Saloon Join Date: Jul 2011
Location: Gävle
Posts: 2,534
Thanks: 395
Thanked 823 Times in 652 Posts
|
|
5th February 2021, 21:59 | #18 |
Avid contributor
Rover 75 Saloon CDTi, MG ZT CDTi Join Date: Apr 2016
Location: Portarlington
Posts: 135
Thanks: 66
Thanked 25 Times in 19 Posts
|
Ok so I have been able to restore the file using 50.00.43..thing is it has made no difference. So I must of saved the file after the change.
Flip... So can I use the LCM file on my LCM and reset it?
__________________
Working on: Rover 75 CDTi Copperleaf Today is just yesterdays tomorrow..... |
6th February 2021, 08:02 | #19 |
I really should get out more.......
Rover 75 Saloon Join Date: Jul 2011
Location: Gävle
Posts: 2,534
Thanks: 395
Thanked 823 Times in 652 Posts
|
Sorry not sure I understand - have you used the LSM file from here?http://toaf.roverki.eu/index.php/en/download-en
Regards |
7th February 2021, 16:44 | #20 |
Avid contributor
Rover 75 Saloon CDTi, MG ZT CDTi Join Date: Apr 2016
Location: Portarlington
Posts: 135
Thanks: 66
Thanked 25 Times in 19 Posts
|
OK so I have used a second hand LSM, I got from the scrape yard. I copied over my Vin to the replacement LSM and changed the Mileage to match my car. I then saved it. I then backed up the LSM and restored that to my original LSM and all is now working.
Yesssss
__________________
Working on: Rover 75 CDTi Copperleaf Today is just yesterdays tomorrow..... |
|
|