|
||
|
20th September 2015, 18:02 | #11 | |
This is my second home
Rover 75 CDT-2001 Join Date: Jan 2009
Location: Wrexham, North Wales
Posts: 3,606
Thanks: 195
Thanked 606 Times in 501 Posts
|
Quote:
image.jpg It now has new springs, new roll bar bushes, new rear drop links, and is now just waiting to go up on the ramps to torque everything up. All new bolts and failsafe washers used. Will be putting new brake disks and pads as well, then hopefully will be ok for the MOT in a couple of weeks. |
|
20th September 2015, 18:06 | #12 |
This is my second home
Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4. Join Date: Jul 2009
Location: Hampshire
Posts: 11,549
Thanks: 3,470
Thanked 3,119 Times in 2,247 Posts
|
That is as good as new then David. Looks great.
I have spare front and rear subframes in the garage so might go down the same route when I get a bit of spare time. |
20th September 2015, 18:21 | #13 | |
This is my second home
Rover 75 CDT-2001 Join Date: Jan 2009
Location: Wrexham, North Wales
Posts: 3,606
Thanks: 195
Thanked 606 Times in 501 Posts
|
Quote:
It is a bit heavy to manipulate back with all the bits on, but 2 trolley jacks helped guide it in to place and the long fixing bolts helped, once the first one was back in it was easy. Still have to repair the heat shields, as the bolts have all pulled through so while i have the exhaust off will be a good time to fit them back with big penny washers and some stainless bolts. I will also derust and paint up the bracing bars in on the tunnel. Broke the back of the job now, its been sat there for 3 weeks with its back end off so will be good to see it back on its wheels. Not too happy with the looks of the fuel tank straps. But they will have to wait until after the MOT |
|
25th September 2015, 19:39 | #14 |
This is my second home
Rover 75 CDT-2001 Join Date: Jan 2009
Location: Wrexham, North Wales
Posts: 3,606
Thanks: 195
Thanked 606 Times in 501 Posts
|
Rear subframe, upper and lower arms, springs, discs shoes and pads, all refitted today.
My short stubby 18mm spanner that i bought from ellesmere market in a set of 10 for a fiver solved the trouble with spinning captive nuts. There is just room for it to go in from the top of the subframe while you torque up the inboard bolts, and use a proper hex nut instead of those silly round ones. I bought new handbrake shoes from pagid, and new discs from mtek. Found them a bit tight to get the drum over the shoes, but they did go on. I am expecting to take the first test drive in over a month tomorrow so fingers crossed there will be no knocks or rattles. The rear wheel arch liners were also removed, and the arches painted, then sprayed with underbody hardwax. Its looking like a new car underneath again. It will be good to see it with its wheels back on. |
3rd April 2018, 01:46 | #15 | |
I really should get out more.......
ZT CDTi 135, ZT260SE Join Date: Feb 2011
Location: Dundee
Posts: 2,877
Thanks: 10
Thanked 331 Times in 213 Posts
|
Quote:
I think it was your or Brian that have had success with this useless nuts and even more useless cages bolted to the subframe. You fellas just liberally soaked with Plusgas for hours/days beforehand? Ive fallen victim to these before, and I don't want to fall victim again. Im aware they are nyloc, so applying heat is a no-no. Even if you had the hands of a squirrel or some other magnetic and bendy tools, Im pretty sure there isnt enough space to push the nuts up and out and replace them. |
|
3rd April 2018, 10:22 | #16 |
Loves to post
we have a 75 connoisseur cdt se saloon and a 75 conniosser se cdt tourer Join Date: Dec 2013
Location: Romford
Posts: 492
Thanks: 177
Thanked 62 Times in 52 Posts
|
Nope l had this happen to me the other day l had to change the rear subframe in the rain not fun l put some photos up of it later
__________________
I have been driving for 20 years and most of it is in rovers [SIGPIC][/SIGPIC] |
21st October 2019, 11:42 | #17 | ||
Posted a thing or two
Rover 75 Saloon Join Date: Apr 2019
Location: Under the car
Posts: 1,840
Thanks: 210
Thanked 244 Times in 221 Posts
|
Quote:
Quote:
PS. The welded slot /cage idea would have been ok if they'd made it from heavier gauge steel, instead of bendable lightweight stuff. |
||
21st October 2019, 16:41 | #18 | |
This is my second home
Rover 75 CDT-2001 Join Date: Jan 2009
Location: Wrexham, North Wales
Posts: 3,606
Thanks: 195
Thanked 606 Times in 501 Posts
|
Quote:
|
|
21st October 2019, 18:34 | #19 |
Posted a thing or two
Rover 75 Saloon Join Date: Apr 2019
Location: Under the car
Posts: 1,840
Thanks: 210
Thanked 244 Times in 221 Posts
|
What about the cage thing though - wasn't that still in the way?
|
22nd October 2019, 00:44 | #20 |
This is my second home
Rover 75 CDT-2001 Join Date: Jan 2009
Location: Wrexham, North Wales
Posts: 3,606
Thanks: 195
Thanked 606 Times in 501 Posts
|
|
|
|