Steering Wheel Interface lead?

Drewcole81 · 29th June 2011, 14:54

Hello All,

I'm slowly getting there with my system in the ZT, so far I have my Pioneer unit installed so I can use the Blue Tooth and iPod on it (I hate CD's in the car!), I've got my Alpine V12 Amp installed okay and my JL Audio 10inch sub too.
Next job is to get my boot floor made up with a shelf for the amp to mount too and a quick plug so I can take the Sub out when I need the room in there.

What I would like however is the interface lead that enables me to use the steering wheel controls, has anyone used one that suits Pinoneer head units, if so where did you get them from?

thanks

Drew.

raykay · 29th June 2011, 16:47

InCarTech and Autoleads are two manufacturers of adapter leads, it depends what unit was originally fitted, (Harmony, Symphony, Kenwood or a later single DIN unit) which lead you need.

lamuff · 12th July 2011, 17:14

im having the same problem i just fitted a kit from fleebay a pioneer head unit etc.. sounds great but the lead to control the steering wheel does not fit into anything its a big 17 round pin block but i do not have anything to plug this into ? any ideas before i complain

im sure i had the symphony unit as its a connie

raykay · 12th July 2011, 20:31

If the connector has 17 round pins, the original unit would have been a Harmony and the adapter lead needed is an Autoleads PC99X-32 or Incartec 29-623. In each case, a Pioneer patch lead is also needed.

29th June 2011, 14:54	#1
Drewcole81 Avid contributor MG ZT 190+ Join Date: Jan 2011 Location: Maldon Posts: 222 Thanks: 0 Thanked 0 Times in 0 Posts	Steering Wheel Interface lead? Hello All, I'm slowly getting there with my system in the ZT, so far I have my Pioneer unit installed so I can use the Blue Tooth and iPod on it (I hate CD's in the car!), I've got my Alpine V12 Amp installed okay and my JL Audio 10inch sub too. Next job is to get my boot floor made up with a shelf for the amp to mount too and a quick plug so I can take the Sub out when I need the room in there. What I would like however is the interface lead that enables me to use the steering wheel controls, has anyone used one that suits Pinoneer head units, if so where did you get them from? thanks Drew. __________________ MG ZT 190+ Commision Number MG 000426 http://img546.imageshack.us/img546/7055/redbeasty.png

29th June 2011, 16:47	#2
raykay I really should get out more....... Now Other Manufacturer Join Date: Nov 2006 Location: Co. Kerry Posts: 2,786 Thanks: 16 Thanked 310 Times in 283 Posts	InCarTech and Autoleads are two manufacturers of adapter leads, it depends what unit was originally fitted, (Harmony, Symphony, Kenwood or a later single DIN unit) which lead you need. Last edited by raykay; 29th June 2011 at 16:51..

12th July 2011, 17:14	#3
lamuff Avid contributor ROVER 75 TOURER CONNOISSEUR SE Join Date: Jan 2011 Location: plymouth Posts: 234 Thanks: 0 Thanked 2 Times in 2 Posts	im having the same problem i just fitted a kit from fleebay a pioneer head unit etc.. sounds great but the lead to control the steering wheel does not fit into anything its a big 17 round pin block but i do not have anything to plug this into ? any ideas before i complain im sure i had the symphony unit as its a connie

12th July 2011, 20:31	#4
raykay I really should get out more....... Now Other Manufacturer Join Date: Nov 2006 Location: Co. Kerry Posts: 2,786 Thanks: 16 Thanked 310 Times in 283 Posts	If the connector has 17 round pins, the original unit would have been a Harmony and the adapter lead needed is an Autoleads PC99X-32 or Incartec 29-623. In each case, a Pioneer patch lead is also needed.