Go Back   The 75 and ZT Owners Club Forums > The 75 and ZT Owners Club Forums > Technical Help Forum
Register FAQ Image Gallery Members List Calendar Search Today's Posts Mark Forums Read
Notices

Reply
 
Thread Tools Display Modes
Old 21st May 2020, 15:47   #11
SDwil
Newbie
 
MG ZT-T

Join Date: Feb 2020
Location: Wirral
Posts: 10
Thanks: 0
Thanked 0 Times in 0 Posts
Default Update

So I’ve eventually had the car in the garage today.

They’ve had a good look and ‘think’ it’s the slave cylinder. They said they have replaced the slave on these previously and on both occasions it didn’t work!

Anyway, they’ve quoted for a slave, master and clutch. To my mind it isn’t worth getting the work done as it’s close to the value of the car. They’ve quoted over 1k for the work which seems very steep to me. Any thoughts?

It’s a decent car, body is good, 155k, usual driver seat wear but overall it’s a good car but I simply can’t justify spending anywhere near that on it.

A bit stuck now as can’t really get the car elsewhere nor do I have the time.

Very frustrating!

Last edited by SDwil; 21st May 2020 at 18:39..
SDwil is offline   Reply With Quote
Old 21st May 2020, 22:04   #12
macafee2
This is my second home
 
Rover 75 Saloon & Tourer

Join Date: Sep 2012
Location: Southampton
Posts: 10,066
Thanks: 1,057
Thanked 1,965 Times in 1,387 Posts
Default

very very expensive, I think going rate has been about £650 but
if AA many said link had snapped they are a long way off. How do they get to the slave being at fault? Going only on your post I don't think they know what is wrong. I think I would find someone else to use
What link is AA man referring to? I thought the one from clutch pedal to master but that's not a gearbox off job. You said on the 11th you would have a look and post what you found, did you look?

I think you would be well advised to follow the advise given already and do a few simple checks, good luck

macafee2

Last edited by macafee2; 21st May 2020 at 22:09..
macafee2 is offline   Reply With Quote
Old 22nd May 2020, 09:34   #13
SDwil
Newbie
 
MG ZT-T

Join Date: Feb 2020
Location: Wirral
Posts: 10
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Thanks for the message.

I took some pictures last week but was unable to upload. Iíll try from my laptop later today and see if that helps.

From what I gather they found some fluid where slave would be. It was explained to me second hand though rather than by the mechanic so Iím going in to pick the car up this afternoon and once I do Iíll get the full version from the mechanic.

Cheers
SDwil is offline   Reply With Quote
Old 23rd May 2020, 14:29   #14
SDwil
Newbie
 
MG ZT-T

Join Date: Feb 2020
Location: Wirral
Posts: 10
Thanks: 0
Thanked 0 Times in 0 Posts
Default

So I've been down and picked the car up. The mechanic explained that with the sealed unit there is fluid visible at both ends. With respect to the clutch he said it was best practice to replace the clutch as the gearbox would have to come out.

Really it needs someone with some experience of these cars to have a look at it and take it from there.

Does anyone know of anyone in the North West that might be able to take a look?

I've tried again to upload some images without success.
SDwil is offline   Reply With Quote
Old 23rd May 2020, 20:54   #15
marinabrian
Live life safely and sensibly
 
marinabrian's Avatar
 
Yes, it's parked outside the window

Join Date: Jan 2011
Location: Plodging in the sea with my dog
Posts: 19,634
Thanks: 3,242
Thanked 10,151 Times in 5,439 Posts
Default

David, I have read through the symptoms you experienced, and although I don't have the eyes on the job so to speak, this is what I suspect has happened.

The quick coupling attaching the pipework from the master cylinder to the slave, has become detached, this results in a solid pedal due to the fluid being unable to exit the master cylinder, and when you press the pedal really hard, the clevis loop at the end of the master cylinder piston breaks.

Now the hydraulic coupling is located directly above the gearbox, and if the coupling is partially detached when the pedal is pressed, then fluid will escape.

What you need to check is whether the clutch master cylinder pushrod is still connected to the clutch pedal, and the clevis loop not broken.

The coupling looks like this..........



The part which I suspect that is broken on the master cylinder, is the thing with the paper tag tied on in this picture.......



Finally this picture shows the position of the clutch master cylinder in relation to the clutch pedal..........



And finally here is a gearbox, to give an idea of where the coupling is located inside the engine bay......



All of these things can be checked with relative ease, and don't require specialist knowledge, and should be discounted before resorting to gearbox removal.

Best of luck

Brian
Attached Images
File Type: jpg clutch coupling.jpg (4.6 KB, 32 views)
__________________
Well I've arrived at end of the road........and I can categorically state this is NOT my second home

Sent from my Jupiter Ace running a 16k RAM pack and Chuck Moore FORTH

O ring failure guide HERE an invaluable guide to O ring failure modes, that don't include nonsense about positioning of clips on KV6 thermostat pipework

Tempus Fugit Memento Mori
marinabrian is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 04:03.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright © 2006-2020, The Rover 75 & MG ZT Owners Club Ltd