|
||
|
14th March 2022, 15:24 | #1 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
Camshaft sensor replacement
My car (2.5 V6) stopped last Saturday March 12th at a petrol station and would not restart. I returned the following day with an Autel diagnostic tool. There was a fault code - camshaft sensor failure. I cleared the fault and the car started ran very well until I got to 120 miles from home. I had stopped at a fuel station on the motorway. Car would not restart. Autel showed camshaft sensor wiring fault got taxi and train home.
I have ordered a new sensor from Rimmels but it is different from the one on the car. The one on the car has the lead as an integral part of the sensor itself. The new sensor has a male socket on top so requires a suitable connecting lead. I also ordered the link lead which appears to go with it. It has a socket at one end that connects with the sensor the other end has a male plug which I hope will connect with the engine harness. My question is- will this sensor and lead marry successfully with the engine? It certainly looks more robust than the current sensor and lead that are on the car at present. I don't want to travel 100 miles on a wild goose foray. I hope someone can tell me whether I am on the path of righteousness or evil. Fred |
14th March 2022, 16:07 | #2 |
Senior Citizen
Rover 75 2.5 Connoisseur SE,Chrysler 300C,124 Spider, Daytona 955i,Honda XL250 & Royal Enfield 650GT Join Date: Feb 2008
Location: The Kingdom of Wessex
Posts: 6,976
Thanks: 2,391
Thanked 2,685 Times in 1,686 Posts
|
As you have spotted, the early sensors had the lead integral but the later ones have a separate lead.
It plugs into the same place and is a straight forward installation. They do look quite different, here is a shot of my old one and the new one that requires a link lead to plug it in. .
__________________
Let the good times roll............ Last edited by Dorset Bob; 14th March 2022 at 16:13.. Reason: Added Image |
15th March 2022, 16:47 | #3 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
camshaft sensor
hello Bob,
Well, I got a new sensor and lead and made the long 120 mile journey with a very obliging friend but it turned into a wild goose chase. I installed the new sensor plus lead and cleared the error on my Autel machine. Car wouldn't start and came up with sensor fail again. I noticed that the petrol pump was not starting up. I disconnected the battery and shorted the battery leads together for about 5 seconds. That seemed to clear the ECU memory but car still would not start so abandoned the project. Do you have any ideas. I thought the cam sensor failure meant that the ignition system did not initiate but the petrol pump would work. I think I recollect that a faulty crankshaft sensor can cause the petrol pump not to start. Do you have any theories? The frustrating thing is that the car was running beautifully until I stopped to check oil and water. Fred |
15th March 2022, 21:30 | #4 |
Guest
Posts: n/a
|
Did you check for the common fuel filter fault? If it separates pressure will be lost and the car won't start.
|
15th March 2022, 21:33 | #5 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
Thanks for your reply but how do I do that and would I need a new filter?
Fred |
15th March 2022, 21:36 | #6 |
I really should get out more.......
Rover 75 Saloon Join Date: Jul 2011
Location: Gävle
Posts: 2,539
Thanks: 395
Thanked 823 Times in 652 Posts
|
Strange that the same fault reappeared even with a new sensor + link lead. There was a problem with one of these link leads being incorrectly wired but I can't remember if it was the cam or crankshaft lead, only that it was Made in Egypt!
Does the rev counter needle move at all during cranking? Good luck |
16th March 2022, 06:36 | #7 |
Loves to post
MGZT Join Date: Aug 2019
Location: Richmond
Posts: 255
Thanks: 26
Thanked 80 Times in 45 Posts
|
Error code
Hi Fred
When my V6 decided to stop working, the breakdown guy plugged in his reader and he said its the camshaft sensor, turned out to be a seized water pump with shredded the timing belt and various other things, I really hope it isn't this. Bob |
16th March 2022, 08:49 | #8 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
I don't think it's the water pump. It was replaced with new cam belts 2000 miles ago and there is no water leak. I am puzzled about the fuel pump not starting. Is the fuel pump disabled if there is a cam sensor fault? If not, then I have a fuel pump problem. The car is 120 miles away and I really can't spend another wasted day running back down to it unless I am reasonably confident of success. A faulty fuel pump relay failure seems to be unlikely to me. The car has only 60,000 miles on the clock so is relatively young.
I am getting too ancient for these wild goose chases! |
16th March 2022, 09:05 | #9 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
Hi Vitesse
I have another sensor and lead that I ordered a while ago by mistake.I am in a quandary as it takes most of a day to drive to the car and return in failure. it looks like I'll have to get the car recovered and go from there. Just more expence! Ouch!! |
17th March 2022, 07:52 | #10 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,446
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Quote:
No it isn't and the problem is unlikely to be the fuel pump.
Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. Last edited by SD1too; 17th March 2022 at 07:59.. Reason: Additions |
|
|
|