Small facelift badge

Bob Williams · 13th October 2013, 09:17

Is anyone aware of the existence os a small facelift badge I could stick on my switch panel to balance the four switches now I have cruise fitted. It needs to be not more than about 3/4 inch high. Mark 1's seem to have little badges everywhere but there are few facelift ones.

Not important but it would just finish it off!

freddie · 13th October 2013, 11:34

Quote:

Originally Posted by Bob Williams

Is anyone aware of the existence os a small facelift badge I could stick on my switch panel to balance the four switches now I have cruise fitted. It needs to be not more than about 3/4 inch high. Mark 1's seem to have little badges everywhere but there are few facelift ones.

Not important but it would just finish it off!

Not sure if this any good.
http://www.ebay.co.uk/itm/Rover-Brus...ht_2167wt_1170

freddie · 13th October 2013, 12:10

Hi Bob just been to check out the one I have.
Its maybe to big the out side dia is inch & an eighthit.
Its on metal back with safety pin type fixing which could be snipped off.
Or the cntre bit is only a plastic sticky badge that could easily prised out,
The out side dia. would then be 7/8 ths.

Bob Williams · 13th October 2013, 13:05

Thanks for the link and especially the dimensions Freddie which tell me it should fit nicely so I have ordered one.

By the way I like your car and many of the mods. I am thinking about puddle lights myself but am unsure whether to go for the battery version or not.

Bob

freddie · 13th October 2013, 15:35

Quote:

Originally Posted by Bob Williams

Thanks for the link and especially the dimensions Freddie which tell me it should fit nicely so I have ordered one.

By the way I like your car and many of the mods. I am thinking about puddle lights myself but am unsure whether to go for the battery version or not.

Bob

The biggest problem with the puddle lights was getting the power into the door ,after many attempts i ended up taking the doors off(ouch).
Unlike how to run power from interior lights across roof and down the pillar.
I ran a wire form the boot light wich also comes on when you open the door.To a block under the front seat . Seeing I had the power there I
Fixed led strip under the seat front and back.
Thus.

Effect at front.

Effect at rear.

13th October 2013, 09:17	#1
Bob Williams Loves to post MG ZT-T+ Join Date: Nov 2010 Location: Milton Keynes Posts: 419 Thanks: 5 Thanked 109 Times in 57 Posts	Small facelift badge Is anyone aware of the existence os a small facelift badge I could stick on my switch panel to balance the four switches now I have cruise fitted. It needs to be not more than about 3/4 inch high. Mark 1's seem to have little badges everywhere but there are few facelift ones. Not important but it would just finish it off!

13th October 2013, 12:10	#3
freddie Passed Away 75 cdti connoisseur se saloon Join Date: Jul 2010 Location: norwich Posts: 11,360 Thanks: 1,171 Thanked 1,921 Times in 1,345 Posts	Hi Bob just been to check out the one I have. Its maybe to big the out side dia is inch & an eighthit. Its on metal back with safety pin type fixing which could be snipped off. Or the cntre bit is only a plastic sticky badge that could easily prised out, The out side dia. would then be 7/8 ths. __________________ [SIGPIC][/SIGPIC][ LADY IN RED

13th October 2013, 13:05	#4
Bob Williams Loves to post MG ZT-T+ Join Date: Nov 2010 Location: Milton Keynes Posts: 419 Thanks: 5 Thanked 109 Times in 57 Posts	Thanks for the link and especially the dimensions Freddie which tell me it should fit nicely so I have ordered one. By the way I like your car and many of the mods. I am thinking about puddle lights myself but am unsure whether to go for the battery version or not. Bob