Andy willi & John's mini nano meet 12/02/2011

[Richy]

Originally Posted by actros

Hi Paul if by any chance you don't get your cae mate you can always come with me .

Thanks Brian, i bet you just want to eat all the cake before we get there

[johnwh74]

Originally Posted by Richy

Thanks Brian, i bet you just want to eat all the cake before we get there

Brian's bringing the cake

No probs Richy - you're more than welcome and we can do whatever needs doing as long as you dont eat all the cake if you do come with Brian

regards John

[johnwh74]

Originally Posted by Devilish

According to the manufacurers spec the Xtrons width is 178mm, the Sion is 183mm. This would mean each side of your trim would need to be 2.5mm narrower than mine.

I have found the email from Simon from when I bought mine, and copied it below.

Hi Stephen

No problem

Just to double check, you need piece No 1 with just the sides (38 mm) and the bottom
I have attached a schematic of your kit as it will look.



PM me your email address and I will send you the schematic above Simon sent me. What you need to do is attach it to an email to him, tell him you want item 1 you made for Stephen from the club, then he will know exactly what you want, but you need the sides of part 1 to be 35mm and the bottom.

I have been watching trebors thread closely, you may want to wait for Simons latest schematic,

PS Some ICE units need removal tools, if you can remove your ICE unit ready that would help

Thanks for the E-mail mate

there are a few pieces that i will be ordering from him and he has said he can do an xbox 360 in walnut, just needs a faceplate from it to copy. Should look amazing if we can get it all tied in and working

regards John

[J1MBO]

Originally Posted by J1MBO

Spoke to Andy at Newark, never thought to ask - any chance you'd have the time to fit a BBK throttle body and plenum to my V8. It's a used one, may have to source a couple of missing screws and gaskets before though.

No probs if it's a bit much, still attending either way.

Cheers


Jim

Originally Posted by andy willi

cant see a problem fitting it

andy

Just found out current insurers don't allow ANY engine mods so I'll not want this fitting now - still got six months to run on the policy.

I'll still be attending though.

Cheers
Jim

[v-man]

Originally Posted by J1MBO

Just found out current insurers don't allow ANY engine mods so I'll not want this fitting now
Jim

Thats too bad Jim. Seems a fair few companies won't cover performance mods on Rovers, though cosmetic changes are ok if notified.

[johnwh74]

Originally Posted by J1MBO

Just found out current insurers don't allow ANY engine mods Cheers
Jim

What's the saying......

what they dont know wont hurt them

Ok Jimbo no probs mate - would of been interesting though

regards john

[J1MBO]

Originally Posted by v-man

Thats too bad Jim. Seems a fair few companies won't cover performance mods on Rovers, though cosmetic changes are ok if notified.

Yes seems so Ian, don't think they'll be getting my business again in six months time. Don't want to repeat what they said when I asked about putting a provisional licence holder on the policy...............

Originally Posted by johnwh74

What's the saying......

what they dont know wont hurt them

Ok Jimbo no probs mate - would of been interesting though

regards john

I know what you're saying John, but knowing my luck I'd have been caught out if I'd had it fitted and not declared it.

Still could be interesting for you though, you might end up fitting it but to another car........

Cheers
Jim

[rrobson]

john, do you get part worns in? if not, how much for two 195/60/15?

cheers mate

[starbug2]

well i hope the meet will go well and i'm sure it will they have much knowledge and all the stuff garages have so i'm sure you will get much done apart from cake and hobnobs and much coffee i'll think of you lot while i make do with being in Bournemouth for a sci-fi convention ,well makes a change from going to car meets

[johnwh74]

Originally Posted by starbug2

well i hope the meet will go well and i'm sure it will they have much knowledge and all the stuff garages have so i'm sure you will get much done apart from cake and hobnobs and much coffee i'll think of you lot while i make do with being in Bournemouth for a sci-fi convention ,well makes a change from going to car meets

Thanks for the 2 x choc hobnobs - damn shame i forgot Andy cannot eat them

Was good to see you mate - hope you can make the next one. Enjoy your convention. LLAP

John