Premium bumper & grille supplier - Page 53

trebor · 3rd March 2012, 21:26

If that is the splitter its a poor diagram, but no matter as Rimmers are out of stock as expected.

Yes you will need one as i did, you could get away without and tie grip the undertray to the bumper but much better finish with the splitter and Rover Breakers wont want much for one, if you have headlight washers or plan to get any the tubing runs inside the splitter too#

btw item 7 in the Russian diagram above which were also hard to come by are now available at Lakeland Minis i understand

sworks · 4th March 2012, 07:26

If they are available through South Lakeland mini centre and people don't want to risk postage I can collect and drop off at POL or the National?

T-Cut · 4th March 2012, 10:54

I have the upper bracket, but thank you. It's the splitter gizmo I'm unclear about. Is this similar to the Seat Leon thingy people are fitting?

TC

trebor · 4th March 2012, 11:16

Quote:

Originally Posted by T-Cut

I have the upper bracket, but thank you. It's the splitter gizmo I'm unclear about. Is this similar to the Seat Leon thingy people are fitting?

TC

yes it does have a good cosmetic look to it and this is the best picture i can find at the minute, when its stops raining I will take some pictures of mine for you

as said as well as the look of it you will need it if doing the premium bumper mod as it fits between undertray and bumper, it is one piece that goes across the front end but note how it is deeper at both ends than in the middle

Devilish · 4th March 2012, 11:52

It is item 2 TC

DPF000050

Quote:

Originally Posted by T-Cut

Ah. I don't think my photo is the right bit. The splitter you show is a moulded strip which I've not seen before. Do you have the Part Number?

EDIT: It's Item 2 here.

This drawing is displayed for both MG and 75 versions.

TC

Typhoon190 · 4th March 2012, 12:25

Quote:

Originally Posted by trebor

yes it does have a good cosmetic look to it and this is the best picture i can find at the minute, when its stops raining I will take some pictures of mine for you

as said as well as the look of it you will need it if doing the premium bumper mod as it fits between undertray and bumper, it is one piece that goes across the front end but note how it is deeper at both ends than in the middle

A bit off track, but that is a stunning looking car. An MG ZT coupe would be even better for me too.

sworks · 4th March 2012, 12:52

Quote:

Originally Posted by trebor

as said as well as the look of it you will need it if doing the premium bumper mod as it fits between undertray and bumper, it is one piece that goes across the front end but note how it is deeper at both ends than in the middle

don't think mine has one of these fitted? will have a look when the Mrs comes home in it!

sworks · 4th March 2012, 13:36

Think I was getting confused, no rubber splitter but there is a piece of plastic trim between the undertray and bumper due to the bumper sitting a few inches lower

woolleysox · 4th March 2012, 15:31

I think its item 14 on the V8 brea

kdown I have one fitted to my ZTT 260and as Trebor said Rover breaker have them.
Rimmers part no
http://www.rimmerbros.co.uk/Item--i-DPF000050 listed as nolonger available.

Quote:

Originally Posted by T-Cut

Yes, this is it: http://www.rimmerbros.co.uk/ItemList...yshell--m-3084

They seem to have missed off the Rover 75 front end. The under piece (Item 2) seems unique to the V8 so I assumed this was the splitter.

The Russian site shows the Rover Premium bits, but no splitter.

Anyhow, you say I'll need one to close the front edge?

TC

woolleysox · 4th March 2012, 16:05

TC do you have the link for the 75/zt Russian site please.

3rd March 2012, 21:26	#521
trebor This is my second home Rover 75 CDTi Connoisseur SE & MG ZT Saloon 190 Join Date: Jun 2007 Location: Coven Posts: 12,523 Thanks: 526 Thanked 1,877 Times in 885 Posts	If that is the splitter its a poor diagram, but no matter as Rimmers are out of stock as expected. Yes you will need one as i did, you could get away without and tie grip the undertray to the bumper but much better finish with the splitter and Rover Breakers wont want much for one, if you have headlight washers or plan to get any the tubing runs inside the splitter too# btw item 7 in the Russian diagram above which were also hard to come by are now available at Lakeland Minis i understand __________________ www.midlandsnanomeets.co.uk Robs Car Gallery Coven near Wolverhampton WV9 2000 Cowley Built Rover 75 2.0 V6 Club SE/ Atlantic Blue/ Sandstone/Walnut (daily driver) 2003 Land Rover Freelander 1 TD4 HSE Helsinki Blue/Black Leather (swmbo daily driver)

4th March 2012, 07:26	#522
sworks Been absent for a while… Rover 75 Tourer, Classic mini Cooper S, Abarth 595 competizione, MG TF and a Hyundai Tucson PHEV Join Date: Feb 2007 Location: Cumbria Posts: 13,065 Thanks: 1,033 Thanked 1,686 Times in 1,040 Posts	If they are available through South Lakeland mini centre and people don't want to risk postage I can collect and drop off at POL or the National? __________________ ................................................. 'Marmite' Possibly one of the most famous 75 tourers produced! left the production line as the last of only Three Rover 75 tourers produced in Trophy Yellow. 48 hours later Longbridge closed. The last sold ordered 75 Tourer. Paid for by the Phoenix Four and handed over by John Towers to the Warwickshire Northampton Air ambulance service as a Rapid Response vehicle

4th March 2012, 13:36	#528
sworks Been absent for a while… Rover 75 Tourer, Classic mini Cooper S, Abarth 595 competizione, MG TF and a Hyundai Tucson PHEV Join Date: Feb 2007 Location: Cumbria Posts: 13,065 Thanks: 1,033 Thanked 1,686 Times in 1,040 Posts	Think I was getting confused, no rubber splitter but there is a piece of plastic trim between the undertray and bumper due to the bumper sitting a few inches lower __________________ ................................................. 'Marmite' Possibly one of the most famous 75 tourers produced! left the production line as the last of only Three Rover 75 tourers produced in Trophy Yellow. 48 hours later Longbridge closed. The last sold ordered 75 Tourer. Paid for by the Phoenix Four and handed over by John Towers to the Warwickshire Northampton Air ambulance service as a Rapid Response vehicle

4th March 2012, 16:05	#530
woolleysox This is my second home Black V8 Ztt 260SE Join Date: Feb 2009 Location: Birmingham Posts: 3,833 Thanks: 391 Thanked 242 Times in 195 Posts	TC do you have the link for the 75/zt Russian site please. __________________ [SIGPIC][/SIGPIC]member 621http://forums.75-zt.com/images/smilies/oldman.gif www.midlandsnanomeets.co.uk

4th March 2012, 10:54	#523
T-Cut This is my second home Rover75 and Mreg Corsa. Join Date: Nov 2006 Location: Sumweer onat mote o'dust (Sagin) Posts: 21,753 Thanks: 341 Thanked 3,660 Times in 2,924 Posts	I have the upper bracket, but thank you. It's the splitter gizmo I'm unclear about. Is this similar to the Seat Leon thingy people are fitting? TC