|
||
|
20th March 2020, 16:50 | #1 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
Replacing cylinder heads on your own
Replacing the rear cylinder head is very difficult if not impossible to do on your own. This is my solution.
You suspend the head complete with exhaust and inlet manifolds from the ends of the inlet camshaft. You can do this either with the engine hoisting bracket as I have done in the picture or you can simply tie a piece of suitable cord between the two camshaft ends and hook on to that. You line everything up by eye and lower gently until the head is about two inches from the block face. You now make final alignment adjustments. Notice that the faces of block and head are almost parallel. (I’m sure Rover didn’t plan that!) You enter the two top centre cylinder head bolts. If alignment is correct they will enter both head and block. These are meant as a guide only at this stage. Now lower the block a fraction until the bolts catch their threads. Then tighten the bolts with your fingers. This brings the faces of head and block parallel. Lower very gently until the dowels enter their allotted holes. That’s it! You can do the same with the front head. |
20th March 2020, 19:10 | #2 |
same car since 2005
2001 Rover 75 2.0 v6 Connoisseur Saloon Join Date: Nov 2006
Location: Ellesmere Port , Cheshire
Posts: 3,811
Thanks: 379
Thanked 549 Times in 466 Posts
|
Very good tip , Fred
It is indeed a long reach for a heavy piece of engine . Not having an engine hoist , I had to call in my brother and then pay him in beer
__________________
Who said it was simples ? |
20th March 2020, 19:20 | #3 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
If he is anything like my brother that must have been expensive! On the other hand what are brothers for otherwise; it's the thickness of blood that counts. You should look into persuading him to buying you an engine hoist though. I don't think they're all that expensive.
|
21st March 2020, 08:52 | #4 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,372
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Quote:
Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
|
21st March 2020, 11:21 | #5 |
Avid contributor
Rover 75 Saloon Join Date: Jun 2018
Location: Ballynahinch
Posts: 194
Thanks: 69
Thanked 60 Times in 23 Posts
|
I needed to change the engine in my wife's citroen ZX years and years ago. The hiring fee was £50 so I looked on Ebay and you could buy one for £150. I argued that in the rest of my life I might use such a thing more than 3 times so I bought. My decision proved to be correct and after rupturing a muscle moving a 150llb gearbox + overdrive I never lift heavy weights without the assistance of Mr. Hydraulic anymore. I see that hoists are still round about £150. Probably chinese and loaded with corona virus Chain blocks are even cheaper and better in some ways.
Fred |
21st March 2020, 20:27 | #6 |
Gets stuck in
MG ZT-T Join Date: Jun 2016
Location: White Rock, BC on Canada's Pacific Coast
Posts: 849
Thanks: 338
Thanked 367 Times in 210 Posts
|
I changed the front head on my Freelander a couple of years ago although I did it with the manifolds removed.
You don't realise just how heavy they are until you try to gently lower it those last couple of inches! The rear would be much more difficult. Good idea using your hoist! I have put my engine hoist to use many times, not always for engines. TR7 Gearbox swap...………………………………………………………………………………………………………………… …………...…………... MG ZA Magnette Engine......…………………….............................. .......................................….MGF Gearbox swap
__________________
ZT-T190, Anthracite, LHD, Left the Line on June 24, 2002, Sold new in Switzerland, spent time in Germany, Imported to Canada in September 2021 Last edited by Rich in Vancouver; 22nd March 2020 at 16:01.. |
22nd March 2020, 00:27 | #7 |
Owners Club Director
Rover 75 Join Date: Oct 2006
Location: Sherfield-on-Loddon
Posts: 4,872
Thanks: 137
Thanked 996 Times in 444 Posts
|
Nice supercharger on the motor there, Rich.
|
22nd March 2020, 15:42 | #8 |
Gets stuck in
MG ZT-T Join Date: Jun 2016
Location: White Rock, BC on Canada's Pacific Coast
Posts: 849
Thanks: 338
Thanked 367 Times in 210 Posts
|
Cheers guys!
I got quite carried away with my ZA, and truth be told I never should have sold it. It was the old story, I did just about everything I wanted to it and got bored. I bought the car out of San Diego and it was absolutely rust free which was a treat. It ended up with a .060 bored and balanced 3-main 1800 from an early MGB with an alloy head and an Eaton/Moss supercharger. An MGB overdrive gearbox and MGB rear end gearing. The best part was the wheels and brakes. Genuine MGA Twin-Cam knock off wheels with 4 wheel disc brakes, MGB front, MGF rear. The Twin-Cam guys were horrified! It was quite fast for a 1950's saloon and surprised quite a few other drivers who thought they could outrun it.
__________________
ZT-T190, Anthracite, LHD, Left the Line on June 24, 2002, Sold new in Switzerland, spent time in Germany, Imported to Canada in September 2021 Last edited by Rich in Vancouver; 22nd March 2020 at 15:57.. |
22nd March 2020, 18:52 | #9 |
Discount MG Rover Spares
Rover 75 CDTi, 2x MG ZS180 Join Date: Jun 2011
Location: Hythe, Southampton
Posts: 11,320
Thanks: 456
Thanked 3,377 Times in 2,027 Posts
|
That looks fantastic! What a motor
__________________
Your trusted MG Rover specialist! Tel: 02380 001133 / Email: [email protected] We now have a 'chat' function on our site for even quicker replies. Give it a try! Remember - discount code FORUM5 for 5% off |
22nd March 2020, 18:57 | #10 | |
Gets stuck in
MG ZT 260, Rover 75 Connie SE auto Join Date: Feb 2013
Location: Redruth
Posts: 984
Thanks: 1,324
Thanked 399 Times in 271 Posts
|
Quote:
|
|
|
|