|
||
|
21st May 2021, 19:34 | #1 |
Posted a thing or two
rover 75 club se Join Date: Apr 2011
Location: Leicester
Posts: 1,644
Thanks: 358
Thanked 419 Times in 310 Posts
|
front backplate bolts
does anyone know the size threads of the front disc backplate mounting bolts please. they are not listed/available from rimmers, thanks.
|
21st May 2021, 19:56 | #2 |
This is my second home
MG ZT-T 190 Monogram Typhoon Join Date: Jan 2009
Location: Oxfordshire
Posts: 4,706
Thanks: 328
Thanked 557 Times in 443 Posts
|
I think they're M5, but I'm not 100% certain.
|
21st May 2021, 20:33 | #3 | |
Loves to post
Rover75 tourer Join Date: Jun 2018
Location: Ashton
Posts: 428
Thanks: 121
Thanked 206 Times in 145 Posts
|
Quote:
You must have a crystal ball, I have just fitted a pair of new plates about 20 mins ago. They are M5 x 0.8 with a thread length of 10mm. If you can, get stainless with a flanged head, but mild steel will be OK with a bit of locktite and paint to protect them from rusting in the future. Due to the rusted heads, as round as a wedding ring, I could only get one of the six out by knocking a torx socket on to the head, I cut the heads off the others ( too small and rusty to weld a nut on and got 4 out quite easily, the last one was a muck or nettles job to drill without damaging the threads in the hub and picking the thread out, luckily there is space to go up to M6 and open up the holes in the plates if needed.
__________________
Common sense isn't a gift, it's a punishment because you have to deal with everyone who doesn't have it. |
|
21st May 2021, 21:50 | #4 |
Posted a thing or two
rover 75 club se Join Date: Apr 2011
Location: Leicester
Posts: 1,644
Thanks: 358
Thanked 419 Times in 310 Posts
|
s/st bolts
thankyou kind sir !! just ordered from kays fasteners on the bay. exact sizes. just keep my fingers crossed the old ones dont snap off when come to remove. not an easy place or sensible to start spraying plusgas whilst still on the car in use. still i have small self tapping bolts st/st to quickly put a hole in the hub and mount them if needed. thankyou for your info .. much appreciated.... .... xsport.
|
21st May 2021, 23:07 | #5 | ||
Give to Learn
Freelander 2 Join Date: Aug 2010
Location: West Midlands
Posts: 18,709
Thanks: 1,155
Thanked 6,407 Times in 3,874 Posts
|
Quote:
These below would of been your very best friend in the situation with the rounded off back plate bolts. https://www.ebay.co.uk/itm/124654484...IAAOSwdJRgXjkb They never fail to remove any rounded of bolt or nut, well have yet to see it. I have several different sets from differing makers. 1 2 3 4 5 6 7
__________________
Arctic Givology Learn to Give Everything is Achievable ad altiora tendo. Check out our Nano meet dates http://www.midlandsnanomeets.co.uk/ http://www.the75andztclub.co.uk/index.php?thepage=howto " You do the work , we supply the expertise " |
||
22nd May 2021, 08:16 | #6 | |
Loves to post
Rover75 tourer Join Date: Jun 2018
Location: Ashton
Posts: 428
Thanks: 121
Thanked 206 Times in 145 Posts
|
Quote:
No problem, if the car is not in use a drop of Plusgas every day will help and yes doing the deed whilst still on the car is doable but if drilling is needed with great care and you will have realised the wheel hub has to be off the drive shaft to get at them, I had the advantage of having them on the bench. For applying Plusgas in small quantities right to the spot, especially difficult to get to places I have an old eye dropper for easy ones and a syringe with various lengths of small bore silicone tubing and a length of brazing rod with a loop bent at 90deg that just grips the end of the tube so I can direct it to the exact spot wherever it is needed
__________________
Common sense isn't a gift, it's a punishment because you have to deal with everyone who doesn't have it. |
|
22nd May 2021, 08:32 | #7 | |
Loves to post
Rover75 tourer Join Date: Jun 2018
Location: Ashton
Posts: 428
Thanks: 121
Thanked 206 Times in 145 Posts
|
Quote:
Hi and thanks Arctic, yes I have a similar selection in my lifesaver extractor, nut splitter, puller, joint splitter, torque multiplier cabinet, along with some ground down torx and spline sockets. However, after a quick rub with a wire brush, I realised tin worm had turned them into nice domed 6.5mm rivets, Brunel would have been proud of . So the start with a 2mm drill bit and crossed had to be done. But like yourself, I don't understand the meaning of the word defeat
__________________
Common sense isn't a gift, it's a punishment because you have to deal with everyone who doesn't have it. |
|
22nd May 2021, 22:23 | #8 | |
Posted a thing or two
rover 75 club se Join Date: Apr 2011
Location: Leicester
Posts: 1,644
Thanks: 358
Thanked 419 Times in 310 Posts
|
Quote:
|
|
23rd May 2021, 06:22 | #9 | |
This is my second home
Rover 75 Saloon & Tourer Join Date: Sep 2012
Location: Lincoln
Posts: 14,926
Thanks: 1,630
Thanked 3,032 Times in 2,181 Posts
|
Quote:
my advice, stay away from Silverline products. I have a couple and they are rubbish quality. macafee2 |
|
23rd May 2021, 08:33 | #10 |
Give to Learn
Freelander 2 Join Date: Aug 2010
Location: West Midlands
Posts: 18,709
Thanks: 1,155
Thanked 6,407 Times in 3,874 Posts
|
Yes bought those back in 2015 used them a few times and they have worked well, these are the shallow type so good for tight spaces, but agree not best make out there, and are only the silverline tools i have, hopefully they will keep on doing me good service when i need to use them.
__________________
Arctic Givology Learn to Give Everything is Achievable ad altiora tendo. Check out our Nano meet dates http://www.midlandsnanomeets.co.uk/ http://www.the75andztclub.co.uk/index.php?thepage=howto " You do the work , we supply the expertise " |
|
|