|
||
|
14th January 2022, 21:55 | #1 |
Can't help myself
Rover 75 CDTi 2005 Join Date: Jan 2018
Location: Lincoln
Posts: 871
Thanks: 469
Thanked 150 Times in 113 Posts
|
Anyone know what this is?
Uncovered this when removing the rear seat from the Tourer today. Photos show the location and corrosion. It's a hollow tube containing what looks like a thin sheathed cable, part of a loom, and a rigid encased something-or-other, possibly a pipe or hose.
The round corroded tube is of quite thin metal. There isn't one on the other side so it wouldn't appear to be structural. What is it please?
__________________
R75 C2 RJBLH Connoisseur CDTi Auto Saloon Built 08/02/2005 @14:57 hrs: Registered 26/08/2005 122nd of 141 built that day British Racing Green Pearlescent (HFF) Sandstone leather with black piping (SPJ) 137,000 miles |
14th January 2022, 22:28 | #2 |
This is my second home
Rover 75 cdt club + Rover 2.5 KV6 Conni SE Join Date: May 2008
Location: Birmingham
Posts: 11,387
Thanks: 6,587
Thanked 2,262 Times in 1,729 Posts
|
I have been warning about this tube that contains the wires that run from the offside wheelarchthrough to in front of the fuel tank for a long while now. Discovered mine was going tommy cotton when I put a new fuel pump in the diesel tank. This is what I believe leads to flooding of the area behind the drivers seat. Mine was not that bad. I cleaned the cavity that runs from The wheel arch to the inside where the ‘pipe’ runs, and then I sprayed some expanding foam back towards the wheel arch into the wheel area. Waited for it to dry, trimmed it, then covered it in underseal.
__________________
Great Barr, Birmingham. |
14th January 2022, 22:31 | #3 | |
Can't help myself
Rover 75 CDTi 2005 Join Date: Jan 2018
Location: Lincoln
Posts: 871
Thanks: 469
Thanked 150 Times in 113 Posts
|
Quote:
Dougie.
__________________
R75 C2 RJBLH Connoisseur CDTi Auto Saloon Built 08/02/2005 @14:57 hrs: Registered 26/08/2005 122nd of 141 built that day British Racing Green Pearlescent (HFF) Sandstone leather with black piping (SPJ) 137,000 miles |
|
14th January 2022, 23:04 | #4 |
Posted a thing or two
rover 75 club se Join Date: Apr 2011
Location: Leicester
Posts: 1,637
Thanks: 358
Thanked 419 Times in 310 Posts
|
the journey starts inside the rear o/s wheel arch. that is the entry point of moisture. you could fabricate something for the tube but you will need to seal the original entry point of moisture. i removed the horizontal cover in the arch, and cleaned the interior surfaces and sealed them with dynax . (you may have to retap the holes and use self tappers or similar) the bolts will be well rusted and may snap off when removing the cover. once you have entry to the (hole) in the wheel arch , after removing the wheel arch liner, you will need to fill this aperture with some kind of a water tight filling. yes this has been flagged up many times before as a potential rot hot spot . .... the mk2 models were less protected than the mk 1 versions and suffer even more readily to this . the covers were available on rimmers but im not sure now. i was lucky to rescue mine and refettle just in time . ....
|
15th January 2022, 07:51 | #5 |
Premium Trader
Rover 75 Join Date: Nov 2010
Location: Devon
Posts: 33,763
Thanks: 8,837
Thanked 14,831 Times in 8,030 Posts
|
Crikey thats a bad one!! It was only the very early mk1s that had the longer cable cover under the wing.
I would be removing one from a scrap car and replacing yours Dougie, a good automotive sealant will hold it in place rather than welding.
__________________
Lest we forget..
|
15th January 2022, 08:11 | #6 |
Gets stuck in
Rover 75 Saloon BRG Join Date: Jun 2007
Location: Retford
Posts: 573
Thanks: 119
Thanked 142 Times in 69 Posts
|
Would the wires be from the fuel filler cap?
|
15th January 2022, 08:20 | #7 |
This is my second home
Rover 75 Saloon & Tourer Join Date: Sep 2012
Location: Lincoln
Posts: 14,912
Thanks: 1,630
Thanked 3,032 Times in 2,181 Posts
|
Christ that looks bad.
I'll be looking out for one of those tubes at the breakers now. macafee2 |
15th January 2022, 08:34 | #8 |
Can't help myself
Rover 75 CDTi 2005 Join Date: Jan 2018
Location: Lincoln
Posts: 871
Thanks: 469
Thanked 150 Times in 113 Posts
|
Well get two then!! (Actually dont. I'm fabricating a fix..)
__________________
R75 C2 RJBLH Connoisseur CDTi Auto Saloon Built 08/02/2005 @14:57 hrs: Registered 26/08/2005 122nd of 141 built that day British Racing Green Pearlescent (HFF) Sandstone leather with black piping (SPJ) 137,000 miles Last edited by goltho; 15th January 2022 at 13:15.. |
15th January 2022, 09:01 | #9 |
Can't help myself
Rover 75 CDTi 2005 Join Date: Jan 2018
Location: Lincoln
Posts: 871
Thanks: 469
Thanked 150 Times in 113 Posts
|
Theres a thick bunch of wires as part of a loom so they may be part of that. Its the thick black ridged pipe that interests me.
Dougie.
__________________
R75 C2 RJBLH Connoisseur CDTi Auto Saloon Built 08/02/2005 @14:57 hrs: Registered 26/08/2005 122nd of 141 built that day British Racing Green Pearlescent (HFF) Sandstone leather with black piping (SPJ) 137,000 miles |
15th January 2022, 09:10 | #10 |
This is my second home
MG ZT-T 190 Monogram Typhoon Join Date: Jan 2009
Location: Oxfordshire
Posts: 4,704
Thanks: 328
Thanked 557 Times in 443 Posts
|
I believe these are the charcoal canister and fuel breather pipes travelling to the fuel tank from the back of the car/fuel filler, hence the reason they are protected by the armouring plate that sits in the osr wheel arch.
Both the armouring plate and the tube that passes the pipes inside the car under the rear bench have corroded away on my 75. The bend sits slightly lower than the entry/exit points so will collect a small amount of water leading to corrosion. Not a great design, but I guess has lasted the average age of a car. |
Thread Tools | |
Display Modes | |
|
|