|
||
|
25th August 2013, 00:51 | #1 |
Give to Learn
Freelander 2 Join Date: Aug 2010
Location: West Midlands
Posts: 18,726
Thanks: 1,155
Thanked 6,407 Times in 3,874 Posts
|
Steering Wheel Fitting (replacement)
Today after yet another cleaning out of the shed i found the steering wheel i was going to replace my slighty marked old one with on the MG ZT, bit like out sight out of mind so decided no time like the present.
Below is how i went about fitting it probably no different than to anyone else but thought photo's may help new members whom have not undertaken this job before and might be thinking of doing it in the future. (Make sure you have your radio code) First get yourself a little torch and take a look at the angle of the torx bolts 30mm which hold the air bag facia onto the steering wheel Fig 1 & 1a-b-c 1 Torx 30mm Fig 1a 1a The tools you will need are torx 30mm, 13mm spanner,16mm long socket and a bar,and a small fine screwdriver. Fig2-3 2 3 Loosen the first torx bolt Fig 4 4 Start engine and turn the steering wheel round and loosen the other torx blots 30mm Fig 5 5 Now make sure the wheel is straight and turn off the engine and disconnect the battery, once disconnected leave for at least 30 minutes get the new wheel ready have a coffee etc Fig 6 6 The new steering wheel ready for exchange with the old one Fig 7 7 Now the 30 minutes have passed you are ready to undo the torx bolts fully Fig 8 8 Once undone the air bag is ready to be lifted up and forward so you can unplug the wiring, you would be best sitting the the drivers seat now for full removal of the air bag, the torx bolts will stay where thay are as they are captive Fig 9 9 Turn the air bag clockwise and over and rest it on the steering wheel bottom rim upside down Fig 10-11 10 With the air bag turned over you will see a yellow and blue locking catch Fig 11 11 The yellow and blue locking catch will need to be removed next do this with the thin small screwdriver Fig 12 12 This will prise open easy Fig 13 13 You can now lift the locking catch up fully Fig 14 14 The yellow wiring plug can now be disconnected by pulling up gently Fig 15 15 The air bag can now be set to one side out of the way, the next step is to unplug the steering wheel harness which serves the horn and remote audio, and the cruse control switch if fitted Fig 16 16 Press and pull free Fig 17-18 17 18 With the harness plug removed we/you can now remove the steering wheel bolt 16mm Fig 19 19 Make a quick mental note of the lining up pointer on the steering wheel Fig20 20 Make sure you have the steering wheel lock on with steering wheel in the up right postion as possible front wheels straight, now fit the 16mm long socket and bar onto the bolt ready to release the bolt Fig 21 21 Hold the steering wheel also if you need to as the bolt can somtimes be very tight Fig 22 22 Once the bolt as been released you can undo it with the socket or your fingers which ever you prefer Fig 23-25 23 24 25 With the bolt removed you will now be able to see the mark on the steering wheel column and the alignment pointer on the steering wheel Fig 26-27 26 27 Now you must feed the yellow air bag wiring and connector through the square hole in the top of the steering wheel as you slowly pull the wheel of the splines and column Fig 28 28 The steering wheel is now removed and the new one can replace it, Fig 29 29 Make sure though that you note the position of the clock spring which the yellow wiring is connected to, you can even tape it up if you like in the position it needs to be, upright in this case to stop it turning but as you will have the new steering wheel next to you on the passenger seat hopefully you don't have to i did not. Fig 30 30 You can now fit the new steering wheel offer it up to the column making sure you align the pointer and the mark on the spline/column also thread through the yellow wiring, if marks are aligned and you are happy push the steering wheel slowly onto the column Fig 31 31 Make sure the plug harness sits square in the top hole Fig 32 32 You can once again check that the marks are aligned by pulling the steering wheel up and little and feel if it moves freely Fig 33-34 33 34 If you are satisfied plug the harness back in at the top Fig 35-36 35 36 The next step is to fit the steering wheel bolt finger tight first Fig 37-38 37 38 Holding the steering wheel and the socket and bar in place fully tighten the bolt do not over tighten, i pinch it up and then a 1/4 turn Fig 39 39 We are now ready to fit the air bag back into position with the air bag cover upside down Fig 40 40 Now locate and offer the yellow locking catch to the air bag pushing down firmly until it plugs fully in Fig 41-42 41 42 Now push home the locking clip Fig 43 43 Make sure the clip is fully locked down Fig 44 44 You can now turn over, clockwise the air bag ready to refit Fig 45 45 With the air bag fitted back in position it can be nipped back up with the two torx bolts from behind Fig 46 46 Reconnect the battery test the horn and indicators etc Fig 47 47 Horns and all the rest working you can now tighten up the torx 30mm do not over tighten so you damage the torx end Fig 48 48 Job is now finished good luck if you intend doing this job Arctic
__________________
Arctic Givology Learn to Give Everything is Achievable ad altiora tendo. Check out our Nano meet dates http://www.midlandsnanomeets.co.uk/ http://www.the75andztclub.co.uk/index.php?thepage=howto " You do the work , we supply the expertise " Last edited by Arctic; 16th March 2021 at 20:46.. |
|
|