|
||
|
4th June 2020, 09:42 | #1 |
Loves to post
Rover 75 saloon 2.0l Diesel Connoisseur Join Date: Apr 2016
Location: Wokingham
Posts: 259
Thanks: 136
Thanked 21 Times in 15 Posts
|
Rumbling from NS, new bearing and driveshaft fitted
Long time no see friends,
I did some work on the old girl recently, changed the front hubs and wheel bearings to brand new stuff from good old DMGRS (hence I'm pretty sure its not the wheel bearing) On the first journey out after the work on the motorway a rumbling very similar to a wheel bearing appeared, I jacked the car up on the offending side, tyre off and had a listen with it spinning, definitely something on the passenger side between wheel and engine, couldnt pin point it anymore than that. To imagine the sound, imagine rolling a brake disc along a concrete driveway (I've tested with the calliper off and the noise is still there) As it has a new wheel bearing I've assumed it was the driveshaft and just replaced that this morning but the noise is still there. To me its either the gearbox or a brand new wheel bearing is failing already?! Any tips would be hugely appreciated kindest regards and TIA
__________________
Gearbox change, clutch, subframe refurbish, handbrake mod, drumbrake repair, rear coils, plate PCB repair, sunroof drains refitted, trim leak fix, cruise control fix, cleared EGR/inlet, new strut bearings, USB sockets in rear ashtray, new front brake pipes/hoses, repaired undertray, new o/s rear upper arm, refurbished rear suspension&subframe, fixed back light leak, new exhaust, fitted HID xenons, FBH fix, new thermostat, armrest LEDs, wood dash, new hydromount, natnav, tyres, numberplates |
4th June 2020, 10:50 | #2 |
MG ZT Join Date: Jan 2011
Location: Newcastle Upon Tyne
Posts: 20,151
Thanks: 3,565
Thanked 10,837 Times in 5,718 Posts
|
Incorrect fitting technique?, poor quality parts?, to be fair it could be either or indeed none of these things, but it is important to not discount items which have been recently replaced as not defective
Start by removing the driveshaft from the hub, backing off the caliper, then spinning the wheel, this should at least exclude the gearbox as a possibility Best of luck Brian |
4th June 2020, 14:30 | #3 |
Loves to post
Rover 75 saloon 2.0l Diesel Connoisseur Join Date: Apr 2016
Location: Wokingham
Posts: 259
Thanks: 136
Thanked 21 Times in 15 Posts
|
I shall have to pull it all apart again and try something!¬ unfortunately its the kind of noise you dont hear until about 20mph and up so spinning the wheel by hand is a tricky test
__________________
Gearbox change, clutch, subframe refurbish, handbrake mod, drumbrake repair, rear coils, plate PCB repair, sunroof drains refitted, trim leak fix, cruise control fix, cleared EGR/inlet, new strut bearings, USB sockets in rear ashtray, new front brake pipes/hoses, repaired undertray, new o/s rear upper arm, refurbished rear suspension&subframe, fixed back light leak, new exhaust, fitted HID xenons, FBH fix, new thermostat, armrest LEDs, wood dash, new hydromount, natnav, tyres, numberplates |
6th June 2020, 08:36 | #4 |
This is my second home
All Trophy Blue ,ZT260#50 , ZT CDTI Auto, ZR105+ and 1.8T Firefrost spoiling the Set . Join Date: Nov 2006
Location: Nr Sherborne But in Somerset..
Posts: 6,076
Thanks: 916
Thanked 1,214 Times in 768 Posts
|
have you looked at the intermediate drive support bearing ?
mine was like a dogs thngy in a bucket .. C
__________________
The Three Bloo's Wifey's Zr105, MY CDTI & 260 #50 and Number One sons 1.8T in Firefrost When I were a lad Zero to 142 in 10.25 secs at the Pod on my Blown Norton. 210 Kart Champ in 70's |
10th June 2020, 20:13 | #5 |
Loves to post
Rover 75 saloon 2.0l Diesel Connoisseur Join Date: Apr 2016
Location: Wokingham
Posts: 259
Thanks: 136
Thanked 21 Times in 15 Posts
|
dont say that! I swapped the gearbox out a while back and have no wish to repeat! haha
Ill have another look and keep my fingers crossed its ok, going to try a cheap wheel bearing i think and see the results, it does seem a remarkable coincidence it was after the bearings were replaced
__________________
Gearbox change, clutch, subframe refurbish, handbrake mod, drumbrake repair, rear coils, plate PCB repair, sunroof drains refitted, trim leak fix, cruise control fix, cleared EGR/inlet, new strut bearings, USB sockets in rear ashtray, new front brake pipes/hoses, repaired undertray, new o/s rear upper arm, refurbished rear suspension&subframe, fixed back light leak, new exhaust, fitted HID xenons, FBH fix, new thermostat, armrest LEDs, wood dash, new hydromount, natnav, tyres, numberplates |
16th July 2021, 19:57 | #6 |
Newbie
MG ZT-T Join Date: Jan 2014
Location: Ellesmere
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
|
Rumbling noise after reaching 25mph
Did you have any luck identifying the source of the rumbling? I have the same problem, new SKF bearing fitted front n/s rumbling started which was n't there before. Grateful for any clues.
|
16th July 2021, 21:58 | #7 | |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Quote:
You could possibly E-Mail him. |
|
|
|