|
||
|
3rd May 2021, 13:30 | #1 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,344
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Drop links: everyone's favourite!
I've bought a pair of MG Rover anti-roll bar drop links direct from X-Part.
Can anyone recommend to me a brand of drop link which does not have these unhelpful features? My current original factory items have lasted over 100,000 miles and 22 years so I am seeking a similar lifespan. Many thanks. Simon Edit: Thread resolution following post no. 108 The answer to my question is no. Expect a struggle removing the old links due to corrosion, poor access and 50% visibility. Fitting all the new drop links as supplied requires ground down spanners and/or shortened threads at the strut mounting (as done by Arctic). Replace the standard enlarged 17mm AF Nylok nut with the original smaller 15mm AF flanged locknut (part no. FX110057) for improved spanner access. A 15mm bicycle cone spanner is adequate on the flats to prevent rotation and damage to the rubber boot. A bi-hexagon flare ring spanner is the best bet for manoeuvrability but its OD will need to be no larger than 25mm to fit the shrouded location and these spanners are usually only available in sets. For the offside it will probably still have to be ground down in thickness. I looked at crow's foot attachments for a torque wrench but they're all too big. Good luck. The job's a lot easier if you have the strut on the bench but you really don't want to do that.
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. Last edited by SD1too; 25th May 2021 at 06:49.. Reason: Adding resolution to a very long and wayward thread |
3rd May 2021, 13:57 | #2 |
This is my second home
Rover 75 Saloon & Tourer Join Date: Sep 2012
Location: Lincoln
Posts: 14,912
Thanks: 1,630
Thanked 3,032 Times in 2,181 Posts
|
Perhaps not answering your question.
Grind the spanner down, cut the thread, this is a common issue, replace the nut with the original? I dont link grinding spanners but I will if I have another two. DMGRS have originals, have a word with them about the spanner size but they dont have an issue if you cut the thread macafee2 |
3rd May 2021, 14:02 | #3 |
Gets stuck in
MG ZT Join Date: Jul 2014
Location: Liverpool
Posts: 850
Thanks: 180
Thanked 248 Times in 189 Posts
|
MEYLE HD, no issues fitting them, are good quality with a 4 year guarantee.
__________________
[SIGPIC][/SIGPIC] |
3rd May 2021, 15:41 | #4 |
Loves to post
Rover 75 Saloon Join Date: Sep 2020
Location: Edinburgh
Posts: 291
Thanks: 133
Thanked 102 Times in 61 Posts
|
I can't recommend a make of droplinks but can recommend using a thin spanner to prevent the rotation. I've done this and the boots did not get damaged.
Like you I also struggled with the top nut. I ended up using a Crows foot, a universal joint and a small extension bar - I'm not recommending this as it was awful The tool for the job is apparently a split ring spanner/flare nut spanner! |
3rd May 2021, 16:00 | #5 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,344
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Neither do I Ian.
Thanks Lee. A good website but the spanner attachment looks thin, just like the MGR parts. I have messaged them. Quote:
Ideally, I would like to buy parts made to the proper OE dimensions so that I can use standard tools. Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
|
3rd May 2021, 16:29 | #6 | |
Gets stuck in
MG ZT Join Date: Jul 2014
Location: Liverpool
Posts: 850
Thanks: 180
Thanked 248 Times in 189 Posts
|
Quote:
__________________
[SIGPIC][/SIGPIC] |
|
3rd May 2021, 16:29 | #7 |
This is my second home
Roverless + 1.7D Sportage Join Date: Aug 2014
Location: East Norfolk
Posts: 7,050
Thanks: 729
Thanked 2,021 Times in 1,449 Posts
|
A pair of large Mole grips will hold the shaft whilst you tighten (or also work for loosening) if the original or replacement is too narrow.
__________________
Oil in my veins! |
3rd May 2021, 16:56 | #8 |
Avid contributor
Rover 75 1.8 Club SE, Rover 75 cdt Club, Rover 75 1.8 Connoisseur SE Join Date: Jul 2015
Location: Inverness
Posts: 163
Thanks: 48
Thanked 44 Times in 27 Posts
|
Agree lifespan of replacements not good. But following thread from I think this site I cut down the thread on the top joint so that a ring spanner can be used to fully tighten. This also makes it a whole lot easier to remove when the time comes.
|
3rd May 2021, 16:57 | #9 |
This is my second home
None Join Date: Feb 2013
Location: None
Posts: 5,556
Thanks: 465
Thanked 1,161 Times in 924 Posts
|
I've always had DMGRS drop links, and sold or written off the car before they wore out. I think I managed to hold them with a spanner but can't remember. Anyway, as above, hold the rod with mole grips until the nut bites down.
|
3rd May 2021, 18:06 | #10 |
This is my second home
MG ZT-T 190 Monogram Typhoon Join Date: Jan 2009
Location: Oxfordshire
Posts: 4,704
Thanks: 328
Thanked 557 Times in 443 Posts
|
Anyone would think it was a hugely difficult task to copy the original part. It's quite a challenge to make something worse, surely.
The Unipart drop links I fitted at the weekend were no better. Impossible to get a standard spanner in without it pushing the rubber boot off. Excellent engineering. |
|
|