Go Back   The 75 and ZT Owners Club Forums > The 75 and ZT Owners Club Forums > Technical Help Forum
Register FAQ Image Gallery Members List Calendar Mark Forums Read
Notices

Reply
 
Thread Tools Display Modes
Old 17th June 2019, 13:23   #1
PC2
Regular poster
 
MG ZT-T 190

Join Date: Mar 2016
Location: Brighton
Posts: 69
Thanks: 4
Thanked 5 Times in 4 Posts
Default ZT-T 190 disappearing oil?

Afternoon.
My ZT-T 190 is using far too much oil. My original 190 never ever used any oil, even well over 100, 000 miles.
My new one has only just done 60K. Its tight, smooth, VIS working well etc.
There are no visible oil leaks.
There is no smoke or residue from exhaust pipe.
Some people mention the breather gauzes and pipes being blocked. Is this likely to use 1/2 litre every 1k miles?
Is this job easy - my back wont allow me to bend over engines for too long anymore, so should I take to a mechanic?
PC2 is offline   Reply With Quote
Old 17th June 2019, 21:38   #2
SD1too
Doesn't do things by halves
 
SD1too's Avatar
 
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model.

Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,265
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
Default

Paul,

There's a particular procedure for checking oil level on the KV6. It must be done with a hot engine and after waiting for a number of minutes. Would you like me to post the procedure?

Simon
__________________
"Whatever is rightly done, however humble, is noble."
Sir Henry Royce.
SD1too is offline   Reply With Quote
Old 18th June 2019, 08:29   #3
PC2
Regular poster
 
MG ZT-T 190

Join Date: Mar 2016
Location: Brighton
Posts: 69
Thanks: 4
Thanked 5 Times in 4 Posts
Default

Hi Simon - thanks for that. Despite finding it difficult to find any level ground in Brighton, I have checked the oil hot and cold and follow the correct steps. For ages I just believed it was because of not finding perfectly level ground, and also perhaps no following the correct procedure, but I am now convinced it is using oil.
I regularly check, but can't work out what is going on.
Any other ideas would be great. Is there a simple way of checking whether the breather holes are blocked? If blocked, can I unblock without taking the head off - ie through the breather pipe connections?
PC2 is offline   Reply With Quote
Old 18th June 2019, 12:09   #4
Canonite
This is my second home
 
BMW 330d Tourer, MG ZT 180 SE XPG, VW Polo 6R 1.2 TDI Bluemotion

Join Date: Jul 2011
Location: York
Posts: 6,020
Thanks: 363
Thanked 574 Times in 319 Posts
Default

Do you have any smoke upon cold start up?
Even if it’s just a small puff of smoke, it would indicate a possible issue with the piston rings in one or more of the cylinders. If you do, pull the spark plugs one at a time when the engine is cold and see what they look like to identify which cylinder it may be.
You may also have a leaky gasket somewhere and the oil is burning off
Canonite is offline   Reply With Quote
Old 18th June 2019, 14:09   #5
PC2
Regular poster
 
MG ZT-T 190

Join Date: Mar 2016
Location: Brighton
Posts: 69
Thanks: 4
Thanked 5 Times in 4 Posts
Default

Hi Canonite
No smoke on starting up or at any other time. The engine feels really tight (its only just done 60K), no rattles, smooth and clear power pick up just over 3000 revs, pulling smoothly to the red line (though I haven't actually ever gone quite that far). That's why I'm so confused. And no particular smell of burning oil after a long run from the engine compartment.
PC2 is offline   Reply With Quote
Old 19th June 2019, 00:33   #6
Rich in Vancouver
Gets stuck in
 
Rich in Vancouver's Avatar
 
MG ZT-T

Join Date: Jun 2016
Location: White Rock, BC on Canada's Pacific Coast
Posts: 844
Thanks: 338
Thanked 367 Times in 210 Posts
Default

Quote:
Originally Posted by SD1too View Post
Paul,

There's a particular procedure for checking oil level on the KV6. It must be done with a hot engine and after waiting for a number of minutes. Would you like me to post the procedure?

Simon
Simon, If you don't mind please post the procedure. Checking the oil on my KV6's drives me to distraction. I usually wait a good long while to check after driving and the measurement varies wildly.
__________________
ZT-T190, Anthracite, LHD, Left the Line on June 24, 2002,
Sold new in Switzerland, spent time in Germany, Imported to Canada in September 2021
Rich in Vancouver is offline   Reply With Quote
Old 19th June 2019, 07:09   #7
SD1too
Doesn't do things by halves
 
SD1too's Avatar
 
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model.

Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,265
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
Default Taking dipstick readings on the KV6 engine

Quote:
Originally Posted by Rich in Vancouver View Post
Simon, If you don't mind please post the procedure.
The following is quoted from an MG Rover bulletin:

"A significant amount of engine oil is retained in the upper levels of the engine. Should a level check be carried out on an engine that has recently been switched off, a low oil level reading may result. This may mislead dealers and customers into concluding that the engine has consumed a quantity of oil.

A revised oil level checking procedure has been developed and will be introduced into future editions of the owners handbook. The procedure is as follows:
Ensure that the engine is at full working temperature. Turn off the engine.
Remove the dipstick and allow the oil to drain down for 5 minutes.
Clean the dipstick and insert it gently into the tube until the 'O' ring on the handle moulding is about to enter the tube.
Slowly push dipstick fully home.
Wait for 5 seconds, withdraw the dipstick and take the level reading.

Should a second reading be required it will be necessary to repeat operations 2 to 5 to allow the dipstick tube to drain down. Similarly, should it be necessary to add oil to the engine, operations 2 to 5 must be repeated."


Is that what you've been doing Paul? It's not easy to see the level when the graticule is black plastic, like mine. Also, oil smears along it as the dipstick is withdrawn and it bears against the tube. I find that pressing it against a sheet of kitchen towel gives the best chance of a meaningful result.

Simon
__________________
"Whatever is rightly done, however humble, is noble."
Sir Henry Royce.
SD1too is offline   Reply With Quote
Old 19th June 2019, 09:18   #8
PC2
Regular poster
 
MG ZT-T 190

Join Date: Mar 2016
Location: Brighton
Posts: 69
Thanks: 4
Thanked 5 Times in 4 Posts
Default

It is pretty much what I do. I will try again today and see when I find some level ground (which I presume also makes a big difference.
On my last ZTT the dipstick was black, stupid idea, so i painted it white.
This ZTT has green tip?
PC2 is offline   Reply With Quote
Old 21st June 2019, 09:46   #9
PC2
Regular poster
 
MG ZT-T 190

Join Date: Mar 2016
Location: Brighton
Posts: 69
Thanks: 4
Thanked 5 Times in 4 Posts
Default

okay, so the car had an oil service in January.
It now oil level on dipstick is halfway between min/max, but that is after adding 1/2 litre of oil.
I have covered 4,200 miles.
I noticed they used 5/40 oil, thinner than the recommended 10/40.

I just don't expect an engine to use oil unless it worn or leaking. Anyone got any ideas?
If it's the cam breathers, do I have to remove the cover and will I need new gaskets?
PC2 is offline   Reply With Quote
Old 21st June 2019, 11:54   #10
SD1too
Doesn't do things by halves
 
SD1too's Avatar
 
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model.

Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,265
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
Default

Quote:
Originally Posted by PC2 View Post
It is pretty much what I do.
Hi Paul,

"Pretty much" means that there's a difference between MG Rover's recommendation and what you've been doing.
Quote:
Originally Posted by PC2 View Post
It now oil level on dipstick is halfway between min/max, but that is after adding 1/2 litre of oil.
So did you take this reading by following MGR's procedure exactly? If so, I would put some more miles on the car and check again to see if it's made any difference.
Quote:
I noticed they used 5/40 oil, thinner than the recommended 10/40.
5W40 is also listed for "all engine types".
Quote:
If it's the cam breathers, do I have to remove the cover and will I need new gaskets?
Yes, you have to remove the camshaft covers. Unfortunately the RH bank requires removal of the manifold chamber first. Remember to observe the torque and sequence for the screws.
The gaskets are metal. I didn't renew mine but some members have reported deterioration of a coating.

Simon
__________________
"Whatever is rightly done, however humble, is noble."
Sir Henry Royce.
SD1too is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 14:18.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright © 2006-2023, The Rover 75 & MG ZT Owners Club Ltd