Can anybody help with one of these please ?

[RogerHeinz57]

Hi folks, I am in need of one of these connectors as a matter of urgency. I found this one on a late 2004 R75 in the n/s/f wiring loom just up from the footwell on the main North to South loom the chunky one). I looked on the drivers side to find nothing similar. The purpose of this connector is to wire up my powerfold mirrors. If anybody can help with this, I would be really grateful.

Link https://drive.google.com/open?id=1Pj...EQWXOC0HWGRJ9G

Many thanks.
ROG.

[trikey]

Is that not the same as a tweeter plug?

[RogerHeinz57]

No, a different size.

[vitesse]

And this one any good?



Regards

[Kwippy1878]

Originally Posted by vitesse

And this one any good?



Regards

Sorry burst your bubble but cars with power folds fitted have a different wiring loom in the doors. The standard loom only has tweeters to plug in but the power fold loom has an extra wire.
Hence why when buying power folds you must get the door looms

[stevestrat]

Door looms for powerfolds can be made up. I got a scrap door loom to get the pins from the door-body connector and switchpack connector. The connectors for the mirrors themselves I found on a computer parts website https://www.startech.com/uk/Cables/C...male~IDC2PIN18. If the cross body wiring isn't there you'd need to get hold of the body side of the door-body connector then follow this excellent guide from Russ:

Originally Posted by BigRuss

How to wire powerfolds:

Check for the wiring being in place both to the drivers door switch pack and to the connectors of the door wiring/ main loom as described in the details below it will save you a load of grief if at least some of it is there.

Remove both door cards and fit powerfold mirrors.

Run a orange 0.5mm cable from connector C0066 pin 4 (powerfold switch plug) long enough to reach connector C0336 pin 14 (drivers side "A" pillar behind the rubber wiring protector to the door) which may be vacant if the wiring isn't there.

Run a orange/red 0.5mm cable from connector C0066 pin 3 (powerfold switch plug) long enough to reach connector C0336 pin 15 which if the wiring isn't present will also be vacant.

At a suitable point both these cables are joined with a shorter length of the appropriate coloured wire that will go to the drivers mirror connection cavity 1= orange, cavity 2 = orange red.

Have fun trying to get the cables fed through the door and rubber wiring protector.

If you are lucky the opposite pins of connectors 14 and 15 of connector C0336 in blue connector C0459 that it plugs into will be already wired, if not run appropriate coloured wires across to the passenger "A" pillar to similar blue connector C0463 this time its pin 8 = orange and pin 9 = orange/red.

In the opposite plug of this connection in connector C0322 pin 8 orange, pin 9 orange/red, run the cables to the passanger door mirror connection noting that this time pin 1 is orange/red, pin 2 is orange.(the opposite way round, this is important )

Of course the appropriate pins would have to be sourced for any missing from the connector blocks. but doing it this way rather than just running two wires means that if you need to remove a door for any reason it can be done normally without having to cut the wiring.

Not forgetting that wiring up the mirrors causes lots of cursing and swearing grazed knuckles and frayed nerves trying to thread the wires through.

Note. The wiring colours I've used in the description are the original colours and missing cables can be substituted for any colours you wish.

Temporarily fit switch and test operation of the mirrors if all is working well, re-fit the doorcards and enjoy

Russ

[RogerHeinz57]

Originally Posted by vitesse

And this one any good?



Regards

Yes that's the one I seek. Have you one available please ?

[vitesse]

Can pop it in the post if you PM me your name / address. I cut it as close to the loom as I could so about six inches of cable included.

Regards

[RogerHeinz57]

Many thanks to Vitesse for his quick supply of this item from Stockholm, not bad thinking that this would be for a British car !