Unused Crown Alloy Wheel.

Norman2CV · 28th January 2022, 19:23

Taken out of the boot of a scrapyard 75 an unused never fitted Crown alloy still fitted with the factory tyre still with label. Ideal for a concours car or restoration. Can send photos by Whatsapp if of interest. Wheel in original sparkling condition . I am in South East Cornwall so somehow needs collecting from there. Must be worth 60 quid ! Have a few other spares, will list over weekend, includes walnut dash, brake calipers, external trim, few interior bits, unused front wishbone. PM for number, also set saloon black pillar panels not rusty ! bumper inserts, rear light, interior light etc etc. take the lot for £100

Andy_with_a_screwdriver · 1st February 2022, 12:46

Is the donor car in a local breakers?
I could do with some spares which you haven't listed.
I'm working in the area all week.
Will send a pm.

Norman2CV · 6th February 2022, 10:37

The car was in line for crushing so i had very limited time to remove some spares, there is also some side trim and bumper trims, and various small bis and pieces.All from a saloon. Will take an offer for the lot if any use to anyone as i no longer have a 75.

JohnnyBG · 6th February 2022, 16:15

jUST CHECKED AND THE SIZE DIFFERS SO NO GOOD FOR ME.

I'm looking for a full size wheel to replace the spacesaver, but the ones on the Rover 75 are 16" seven spoke, there's one on Ebay for £50 plus £20 postage. I wonder if yours would match in with what's on the car for size but seems a waste of a good wheel, all I need is one that's safe to use - cosmetics of no importance at all.

I'll have to check what Crown are like as it might do for the ZT-T, they are low profile. Can't look as it's in for work.

JohnnyBG

Norman2CV · 6th February 2022, 23:06

The Crown alloy was fitted on the Conny and is 15 inch.

28th January 2022, 19:23	#1
Norman2CV Regular poster Rover 75 Saloon. Pre Production. Join Date: Jun 2021 Location: Callington Posts: 90 Thanks: 40 Thanked 72 Times in 25 Posts	Unused Crown Alloy Wheel. Taken out of the boot of a scrapyard 75 an unused never fitted Crown alloy still fitted with the factory tyre still with label. Ideal for a concours car or restoration. Can send photos by Whatsapp if of interest. Wheel in original sparkling condition . I am in South East Cornwall so somehow needs collecting from there. Must be worth 60 quid ! Have a few other spares, will list over weekend, includes walnut dash, brake calipers, external trim, few interior bits, unused front wishbone. PM for number, also set saloon black pillar panels not rusty ! bumper inserts, rear light, interior light etc etc. take the lot for £100 Last edited by Norman2CV; 31st January 2022 at 10:03.. Reason: additions

6th February 2022, 16:15	#4
JohnnyBG Avid contributor ZT-T Join Date: Sep 2019 Location: Teesside Posts: 235 Thanks: 176 Thanked 66 Times in 38 Posts	jUST CHECKED AND THE SIZE DIFFERS SO NO GOOD FOR ME. I'm looking for a full size wheel to replace the spacesaver, but the ones on the Rover 75 are 16" seven spoke, there's one on Ebay for £50 plus £20 postage. I wonder if yours would match in with what's on the car for size but seems a waste of a good wheel, all I need is one that's safe to use - cosmetics of no importance at all. I'll have to check what Crown are like as it might do for the ZT-T, they are low profile. Can't look as it's in for work. JohnnyBG Last edited by JohnnyBG; 6th February 2022 at 16:23.. Reason: ADD INFO.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

1st February 2022, 12:46	#2
Andy_with_a_screwdriver Gets stuck in Rover 75 Tourer CDTi Join Date: Jun 2017 Location: Plymouth Posts: 692 Thanks: 141 Thanked 153 Times in 117 Posts	Is the donor car in a local breakers? I could do with some spares which you haven't listed. I'm working in the area all week. Will send a pm.

6th February 2022, 10:37	#3
Norman2CV Regular poster Rover 75 Saloon. Pre Production. Join Date: Jun 2021 Location: Callington Posts: 90 Thanks: 40 Thanked 72 Times in 25 Posts	The car was in line for crushing so i had very limited time to remove some spares, there is also some side trim and bumper trims, and various small bis and pieces.All from a saloon. Will take an offer for the lot if any use to anyone as i no longer have a 75.

6th February 2022, 23:06	#5
Norman2CV Regular poster Rover 75 Saloon. Pre Production. Join Date: Jun 2021 Location: Callington Posts: 90 Thanks: 40 Thanked 72 Times in 25 Posts	The Crown alloy was fitted on the Conny and is 15 inch.