|
||
|
4th March 2015, 17:54 | #1 |
Loves to post
mg ztt Join Date: Oct 2014
Location: Exeter
Posts: 328
Thanks: 2
Thanked 37 Times in 35 Posts
|
Hiline speedo input
HI guys
had to do a unknown run yesterday and thought i would use the hiline i installed, entered destination but had no voice instructions and very slow tracking, after a little research i think i have not cnnected the 2 pin speedo input plug, after removing the speedo to try and find a matching plug and not finding one i failed and gave up., Any ideas as to where it should be? car is a facelift zt-t cdt Thanks |
4th March 2015, 20:56 | #2 |
I really should get out more.......
MG ZT-T, Rover 75 Tourer Join Date: Mar 2011
Location: Olney
Posts: 2,969
Thanks: 245
Thanked 1,088 Times in 657 Posts
|
Never seen a 2 pin plug on a highline loom?
|
4th March 2015, 21:53 | #3 |
Loves to post
mg ztt Join Date: Oct 2014
Location: Exeter
Posts: 328
Thanks: 2
Thanked 37 Times in 35 Posts
|
Oh ok now confused, i have a 2 pin plug that is up near the board monitor looks the same as would plug in to the back of a cigar 12volt socket,
i thought this was for the speedo input as everything else works on the system just not the navigation voice/tracking. ??? help please. Thanks Nathan |
5th March 2015, 07:13 | #4 |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
there's a small plug that goes into the main body harness near the ash try....it picks up a signal from the ABS unit.
Very early cars didn't have it...
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
5th March 2015, 07:18 | #5 |
I really should get out more.......
MG ZT-T, Rover 75 Tourer Join Date: Mar 2011
Location: Olney
Posts: 2,969
Thanks: 245
Thanked 1,088 Times in 657 Posts
|
The feed from the ABS ecu should be in the ISO connector of the main car loom.
Still cant recall a 2 pin plug like that anyway except on the cigar socket?? |
5th March 2015, 07:24 | #6 |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
Phil - its in a short fly lead adjacent to the end of the Hiline loom....
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
5th March 2015, 07:24 | #7 |
This is my second home
75 Join Date: Nov 2006
Location: Leeds
Posts: 8,432
Thanks: 176
Thanked 907 Times in 716 Posts
|
|
5th March 2015, 07:31 | #8 |
I really should get out more.......
MG ZT-T, Rover 75 Tourer Join Date: Mar 2011
Location: Olney
Posts: 2,969
Thanks: 245
Thanked 1,088 Times in 657 Posts
|
Ahhh i think i know what may have happened, the OP has a facelift car and has probably fitted an earlier loom, i have a full face lift hiline loom here all set up in my living room and all signals go through the standard ISO connector C0098
|
5th March 2015, 07:39 | #9 | |
This is my second home
75 Join Date: Nov 2006
Location: Leeds
Posts: 8,432
Thanks: 176
Thanked 907 Times in 716 Posts
|
Quote:
This was because the grey/green from the ABS unit was not connected. You will need plug C0982 to be connected to your system to get the hi line to work on the move. Dave T |
|
5th March 2015, 18:52 | #10 | |
Loves to post
mg ztt Join Date: Oct 2014
Location: Exeter
Posts: 328
Thanks: 2
Thanked 37 Times in 35 Posts
|
Quote:
so i should have a plug the other side? i have been looking behind the speedo, it may be there as there is a nokia bluetooth kit (not factory fit)stuffed in that side and as such the stereo plug is stuffed behind that and i have adapted the other end of the nokia kit to the hiline loom, i will have a look and see if any of it flows through the nokia kit. I will get a pic of the 2 pin plug i have in the loom for you phil as i have no idea what it feeds. Thanks |
|
|
|