|
||
|
2nd September 2021, 09:35 | #1 |
Avid contributor
MG ZT 190 Join Date: Apr 2016
Location: Heathrow
Posts: 166
Thanks: 109
Thanked 24 Times in 14 Posts
|
Cooling Fan Test
I'm continuing to get my 'other ZT' ready for the road and MOT, which is a 2002 ZT KV6 190, having sorted the front suspension last week i'm now on the cooling system.
I have read the 'How To fan test' written by Jules in depth but still find a couple of actions which don't pan out as I read - assuming I have things correct. Any guidance from knowledgeable peeps will be most welcome! The Issue: There is an intermittent fault stopping the fan cut in at the temperature it should - 100degrees. It did kick in yesterday once, correctly and stop correctly around 96 degrees but then not again. So I then used the 'How To' to test it. First: quote: 'set the AC to demist function' My other ZT has the demist button but not this one as its a different (older) panel. (see piccy) So, do I switch on the ignition/aircon/blower/set to windscreen in order to get to the same state as above? Second: If I'm correct in my assumption - there is no fan action by bridging the gap on the trinary switch plug across the 2 furthest apart terminals, or the two closest together. Then with the engine running, and the AC on, the same test gives nothing across the farthest apart terminals (yellow/grey to black but does give a click ( the aircon clutch I guess) bridging the 2 x closest together. Ive checked the fuses which Jules recommends but not the control box as Ive not got the front off the car yet - in the hope i may not have to! thanks in advance Mal. dash panel.jpg |
2nd September 2021, 10:37 | #2 | ||
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,573
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Quote:
Quote:
1 = slate/yellow 2 = black 3 = yellow/slate 4 = black To check the faster fan speed you need to bridge terminals 2 & 3. Do you have a 2 or 3 speed fan Mal? Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
||
2nd September 2021, 10:42 | #3 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,573
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Kv6
Quote:
Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
|
2nd September 2021, 11:02 | #4 |
Avid contributor
MG ZT 190 Join Date: Apr 2016
Location: Heathrow
Posts: 166
Thanks: 109
Thanked 24 Times in 14 Posts
|
[QUOTE=SD1too;2898180]Yes. Set the centre rotary control fully clockwise to the windscreen demist position. Does the LED in the 'A/C' button illuminate? If not, press the 'A/C' button so that it does.
Hi Simon - the a/c button will only illuminate with the engine running ie not ignition only. When it does .............................see below: Great care is needed identifying the wiring colours. There is slate/yellow and yellow/slate! The first colour is the main one and the second is the tracer. Confirm your identification by looking for the tiny terminal numbers moulded into the plastic connectors: 1 = slate/yellow 2 = black 3 = yellow/slate 4 = black To check the faster fan speed you need to bridge terminals 2 & 3. Do you have a 2 or 3 speed fan Mal? Sorry for the careless colour ID. Yes I agree with the colours and see the numbers too and can confirm Ive been bridging 2 and 3 with out action! (engine running ) I have no resistor gold or silver that I can see so can only assume its an earlier 3 speed. |
2nd September 2021, 12:29 | #5 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,573
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Hi Mal,
If your fan motor is the three speed type then it sounds as if you have the common situation of a worn down earth brush. This will knock out the slow speed (needed to cool the engine at 100˚) as well as the medium speed (which is triggered by the trinary switch bridging you've done). This can be repaired economically with new brushes from Engineering Carbon Products in Croydon which are specially made for our motors. I have these fitted to my own car and they have outlasted the originals. Don't be tempted by cheaper inferior offerings on eBay. Regarding the air conditioning, if the compressor clutch isn't engaging when you press the A/C button the system probably needs recharging but you'll need to fix the fan before dealing with that. If you need any further help, let me know. Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
2nd September 2021, 12:45 | #6 |
Avid contributor
MG ZT 190 Join Date: Apr 2016
Location: Heathrow
Posts: 166
Thanks: 109
Thanked 24 Times in 14 Posts
|
Thanks Simon, how many brushes are in the 3 speed motor? Also can you give the details of the Mobile Aircon guy in Hownslow. Next job front off!
On a slightly different note, do you know if I can fit some sort of media system for phone etc to the panel I have instead of the single Kenwood head unit - (or even a Hi Line as a last resort!) Thanks again for sharing your endless knowledge! Last edited by bluemalbert; 2nd September 2021 at 12:50.. |
2nd September 2021, 15:00 | #7 |
This is my second home
ZT260 #243 (resting) Join Date: May 2010
Location: Prestonpans
Posts: 22,590
Thanks: 650
Thanked 4,624 Times in 3,358 Posts
|
There's four brushes, a set of four from ECP is £36, not sure if that includes P&P. I got a set from them for a 1.8T but that was years ago.
Link to brushes you need: https://engineeringcarbonproducts.co...variant/795934 Not a lot of point in contacting an aircon engineer before the fan is sorted. |
2nd September 2021, 18:33 | #8 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,573
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Hi Mal,
Thanks to Steve for giving the link to Engineering Carbon Products Ltd. They now sell the brushes singly or in pairs or a full pack of 4. I recommend dismantling the motor first to assess how many you need. Regarding your media question, it's best to start a new thread about that in the ICE section. I'll send you a PM with the contact details of the Hounslow based air con. mobile specialist. Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
3rd September 2021, 07:41 | #9 |
This is my second home
Toyota RAV4 Join Date: Jun 2017
Location: Tamworth
Posts: 3,082
Thanks: 2,478
Thanked 1,579 Times in 968 Posts
|
Hi,
You'll find these invaluable - with thanks to Arctic - as usual https://www.the75andztclub.co.uk/for...d.php?t=192903 Go to post #9 for photos And Union Wheels https://the75andztclub.co.uk/forum/s...d.php?t=209950 Good Luck. |
3rd September 2021, 09:41 | #10 | ||
Give to Learn
Freelander 2 Join Date: Aug 2010
Location: West Midlands
Posts: 18,814
Thanks: 1,155
Thanked 6,407 Times in 3,874 Posts
|
Quote:
The OP need to get the back of the motor once he as removed the fan from the car and check the brushes. 1 Also make sure the motor is in decent condition if not scrap the fan. 2 3 Arctic.
__________________
Arctic Givology Learn to Give Everything is Achievable ad altiora tendo. Check out our Nano meet dates http://www.midlandsnanomeets.co.uk/ http://www.the75andztclub.co.uk/index.php?thepage=howto " You do the work , we supply the expertise " |
||
|
|